WR30X10093 Icemaker Replacement – What This Part Fixes and How to Install It
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
WR30X10093 is a GE electromechanical ice maker assembly used in many GE/Hotpoint/Whirlpool-style refrigerators. It controls ice-making cycles (freeze, harvest, and fill). When it fails you’ll typically get no ice, small or hollow cubes, continuous water, or an icemaker that never cycles. Below are step-by-step diagnostics and repair instructions. 1) Preliminary checks (5 minutes) - Confirm model compatibility: verify your refrigerator model accepts WR30X10093 or cross-reference part numbers WR30X30972, AP4345120, PS1993870, 1399596. - Check water supply: ensure the house water shutoff to the fridge is open and water line isn't kinked. Replace the water filter if it hasn’t been changed in >6 months. - Check power: make sure the fridge is plugged in and the freezer is cold (0–5°F / -18 to -15°C ideal for ice production). 2) Quick functional test (5–10 minutes) - Locate the icemaker module in the freezer (usually on the inside wall). Look for a test button or small switch. Press the test button to start a harvest/fill cycle. Listen for the motor running and water filling. - If there’s no test button, you can jumper the motor/feed contacts (consult wiring diagram for your model) momentarily to force a cycle. 3) Interpret results - If the ice maker runs and fills: problem may be intermittent or water supply/partial freeze in the fill tube. Let it cycle; if it works, monitor for 24 hours. - If it runs but doesn't fill: suspect the water inlet valve or water supply line. - If it doesn't run at all: suspect the icemaker assembly, harness, or lack of control voltage. 4) Voltage and continuity checks (use a multimeter; 10–20 minutes) - With the fridge powered and in a test cycle, measure for line voltage at the ice maker fill terminals when the unit is supposed to fill (many systems supply ~120VAC; check your model). If voltage is present but no water, replace the water inlet valve. - With power off, check continuity of the icemaker motor/thermostat contacts per service literature. No continuity or open circuits inside the module indicates a bad icemaker. 5) Inspect fill tube and filter (5 minutes) - Check the fill tube that runs to the ice maker for ice blockages (frozen). If frozen, defrost the tube with warm water or a hair dryer on low (careful with plastic). Replace the water filter if clogged. 6) Remove and replace WR30X10093 (20–30 minutes) Tools: nut driver or screwdriver (usually 1/4" or 5/16"), needle-nose pliers, towel. - Turn off water supply to the fridge and unplug the refrigerator. - Open freezer, remove ice bucket or drawers for access. - Remove the small cover over the icemaker (if present). - Unscrew the two screws holding the icemaker to the freezer wall (usually 2 screws). Carefully tilt and pull the unit out a few inches to access the wiring connector. - Disconnect the wiring harness by pressing the tab and pulling the connector apart. Remove the old icemaker assembly. - Install the new WR30X10093: connect the wiring harness, seat the icemaker on the alignment tab, and resecure with screws. Replace the cover and ice bin/drawer. - Turn water supply back on and plug in refrigerator. - Put the ice maker into a test/advance cycle and verify you hear the motor and see a fill. Check the fill tube for leaks. Allow 24 hours for the first batch of ice. 7) Final checks - If new icemaker still fails to fill but you measured voltage to the valve during fill, replace the water inlet valve. If there is no voltage to the icemaker during a commanded cycle, check the harness and control board. Safety note: Always unplug the refrigerator and shut off the water before disconnecting wiring or valves. Use care when working around sharp metal freezer edges and when testing live voltage—if unsure, hire a qualified appliance technician.
Common Symptoms
No ice production, ice maker doesn’t cycle, small/hollow cubes, continuous water running into ice bin, or only occasional/partial ice production.
Common Causes
- Failed icemaker assembly (WR30X10093 internal motor/thermostat or gears worn out)
- Water supply problems (closed/kinked line, frozen fill tube, clogged filter) or faulty water inlet valve
- Wiring/harness failure or no control voltage from the refrigerator's control board
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Press the icemaker's test button or momentarily jumper the two motor contacts—if the unit doesn't start a harvest cycle but you have continuity/power to the module, the WR30X10093 assembly is likely bad.
Frequently Asked Questions
Will WR30X10093 fit my refrigerator?
WR30X10093 fits many GE, Hotpoint, and some other refrigerators. Always confirm compatibility by checking your refrigerator model number and cross-referencing OEM part lists; the WR30X30972 and AP4345120/PS1993870/1399596 are common cross references. If in doubt, provide your fridge model number before ordering.
Do I have to replace the water inlet valve when replacing the icemaker?
Not necessarily. Replace the water inlet valve only if testing shows the valve does not open when the icemaker calls for water. During a fill cycle measure voltage to the valve—if voltage is present and no water flows, replace the valve. If there’s no voltage, diagnose wiring/control board or the icemaker module first.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.