Whirlpool Drain Pump W10536347 – What Part Fixes Drain and Leak Problems?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What this part is and why it matters: The W10536347 is the drain pump assembly used on many Whirlpool, Maytag and KitchenAid washers. Its job is to remove water from the tub during drain and spin cycles. When the pump fails, the washer won't drain properly, may display drain-related error codes, can hum without pumping, or leak from the bottom. Step-by-step diagnostic and repair instructions: 1) Safety first: Unplug the washer and shut off the water supply. Have towels, a shallow pan or bucket, and gloves ready. 2) Confirm the symptom: Run a drain/spin cycle. Note sounds (humming, grinding, silence) and whether water leaves the tub. 3) Check the easy stuff: Inspect the drain hose for kinks, clogs, or a blocked standpipe/air gap. Remove and clear any visible debris. 4) Access the pump: Depending on model, remove the lower front access panel (or tilt the washer back to access the bottom). Place towels and a bucket under hoses before disconnecting. 5) Inspect the pump visually: Look for obvious leaks, broken or missing impeller blades, and trapped debris (coins, fabric, small objects). Spin the impeller by hand— it should rotate freely. 6) Electrical check: Disconnect the pump’s wiring harness. Use a multimeter to check continuity across the pump motor terminals. An open circuit (infinite ohms) usually means the motor is bad. 7) Functional test (only if comfortable and safe): With the harness disconnected and pump supported, you can briefly energize the pump via the washer’s diagnostic mode to see if it runs — only if you know your model’s safe diagnostic procedure. If unsure, skip and rely on continuity + symptoms. 8) Remove the pump: Drain residual water by loosening the lower hose clamp and draining into a bucket. Remove electrical connectors, release hose clamps, and unfasten mounting screws or clips holding the pump to the washer (some clip; some screw). Note the pump orientation and hose routing. 9) Replace the pump: Install the new W10536347 in the same orientation. Reattach hoses with clamps, reconnect wiring, and secure the pump with its fasteners. Replace the access panel. 10) Test: Reconnect power and run a drain/spin cycle with no laundry. Watch and listen for proper pump operation and check for leaks. Final safety note: Always unplug the washer before working on electrical parts and avoid applying line voltage directly to components unless you are trained and understand the risks.
Common Symptoms
Washer won't drain or spins with water inside; pump hums or makes grinding noises; leaks from the bottom of the washer; drain-related error codes.
Common Causes
- Pump motor failure (electrical burnout or open windings)
- Impeller jammed or broken by debris (coins, small items, lint)
- Clogged drain hose or standpipe causing perceived pump failure
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
If the pump hums but doesn't move water, first remove and inspect the impeller for debris. If the impeller spins freely but the multimeter shows an open circuit across the motor, replace the W10536347.
Frequently Asked Questions
How much does the W10536347 pump cost and is it worth replacing myself?
Replacement pump prices typically range from about $40 to $120 depending on vendor. Labor by a technician can add $100–$200. Many homeowners can replace this pump themselves in 30–60 minutes with basic tools (screwdriver, pliers, socket set, multimeter). Follow the safety steps above and consult your washer’s service manual for access specifics.
Can I run the washer without the drain pump or bypass it?
No. The drain pump is required to remove water from the machine. Bypassing it isn’t practical — the washer will not drain, and attempting makes the machine unsafe. Replace the failed pump (W10536347) or clear the obstruction causing the pump to fail.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.