Part 106532670300 — How to Identify What It Fixes and How to Replace It

Understanding the Problem

Short explanation: I could not definitively identify 106532670300 without the appliance make & model or a photo of the part. Many OEM part numbers look similar across brands, and suppliers often change numbering. Below are step-by-step instructions to identify the part, diagnose the failure, and safely replace it once confirmed. 1) Identify the appliance and part: 1.1) Locate the appliance model & serial number (rating plate). The rating plate is usually inside the door opening, on the back, or behind a kick plate. Record model and serial exactly. 1.2) Remove the part (or take clear photos): capture any markings, shape, connectors, and mounting points. Note connector colors and wire positions. 1.3) Search OEM parts sites and large parts retailers using the appliance model number first, then try 106532670300 as the part number. If online results are ambiguous, contact the brand’s parts department or an authorized dealer with your appliance model and the part number. 1.4) Cross-reference: many parts are listed on parts diagrams as “PN 106532670300”. Confirm the description matches the physical part (e.g., control board, motor, thermostat, latch). 2) Determine what problems this part can cause (general checklist you can use once the part type is known): 2.1) If it’s a control board / PCB – symptoms may include no power, no response to controls, intermittent operation, error codes. 2.2) If it’s a thermal cutoff, thermostat, or heating element – symptoms include no heat, overheating, or tripping thermal protection. 2.3) If it’s a motor or motor assembly – symptoms include no agitation/spin (washer), no drum rotation (dryer), excessive noise, or burn smell. 2.4) If it’s a door latch/lock assembly – symptoms include door won’t lock, “door” error, cycle won’t start. 3) Practical diagnostic steps (general, applicable to most parts): 3.1) Power safety first: Unplug the appliance or switch off the breaker before touching electrical parts. 3.2) Visual inspection: Look for burned components, melted plastic, broken tabs, corrosion on terminals, or loose connectors. 3.3) Use a multimeter: Check for continuity, resistance values, and expected voltages at connectors (with power applied only when safe and necessary). Compare readings to the service manual or typical values for that component type. 3.4) Swap/test if possible: If the part is a plug-in module and you have an identical known-good part (or can borrow one), swap to confirm the fault. For parts like thermostats or thermal fuses, continuity testing usually confirms failure. 4) Replacement steps (general safe procedure to replace an identified part): 4.1) Tools: screwdriver set, nut drivers, multimeter, labels or masking tape and marker, camera or phone, needle-nose pliers. 4.2) Preparation: Unplug appliance and turn off water supply (washer) if necessary. Take photos of wiring and connectors before disassembly. 4.3) Remove access panels: Follow the service diagram for your model to remove panels and reach the part. Keep screws organized. 4.4) Label and disconnect wires: Use labels or take a close photo showing each connector’s position. Pull connectors straight off; avoid tugging on wires. 4.5) Remove the faulty part and install the replacement: Transfer any mounting brackets or gaskets. Ensure connectors seat fully and fasteners are tightened to but not over-torqued. 4.6) Reassemble and test: Refit panels, restore power, and run a test cycle. Observe for correct operation and listen for unusual noises. Safety note: If you are not comfortable working with live electricity, gas connections, or water lines, or the part is inside high-voltage areas (control boards, high-voltage capacitors), stop and contact a qualified appliance technician. Incorrect diagnosis or installation can cause electrical shock, fire, or further appliance damage.

Common Symptoms

Unknown until the part is identified. Typical symptoms related to unidentified parts include: appliance won’t start, error codes, no heat, no motor movement, door won’t latch, intermittent operation.

Common Causes

• Part number ambiguity or manufacturer renumbering (the same physical part may have multiple PN variants)
• Component failure (electrical burnout, mechanical wear, or corrosion)
• Related wiring, connector failure, or upstream component failure causing perceived part fault

Popular Parts That Fix This Problem

These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.

Frequently Asked Questions