TJ90TB123A Dryer — Model Identification & Practical Troubleshooting Guide
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
You supplied: "TJ90TB123A." That looks like a dryer model or label code. If you intended to name a specific part, please resubmit the part number. This guide shows how to confirm the appliance model, where to get the correct parts/manual, and step-by-step diagnostics and repairs for the most common dryer problems. Follow these steps in order: 1) Confirm the model and power type - Locate the dryer model/serial label. Typical locations: inside the door opening on the rim, on the back panel, or on the rear of the dryer cabinet. Note the full model and serial numbers and whether the dryer is gas or electric (gas has a gas line; electric usually has a 240V cord). - If "TJ90TB123A" appears on the label, copy the full line exactly and take a photo for reference. 2) Find the correct service manual and parts list - Use the full model number on the manufacturer's website or at reputable parts sites. Enter the entire model exactly. The manual and parts explosion view are critical — parts are model-specific. - If the manufacturer site doesn’t find it, contact manufacturer customer support with the photo. 3) Common problems to check first (general for most dryers) a) Dryer won't start or has no power - Check house breaker or fuse for the dryer circuit. Reset any tripped breakers. - Confirm the dryer is plugged in and the cord and terminal block are intact. - Inspect the door switch: if the dryer won’t start when the door is closed, a failed door switch is common. - Test start switch and timer or electronic control with a multimeter for continuity. b) Dryer runs but doesn't heat (electric or gas) - Electric: check thermal fuse, high-limit thermostat, and heating element for continuity. A broken heating element or open thermal fuse is a frequent cause. - Gas: check igniter, gas valve coils, and flame sensor. If you hear clicking but no light, the igniter or gas valve can be the cause. - Clean lint from the heater box and venting — restricted venting causes poor heating and long dry times. c) Dryer tumbles but won't tumble (or drum won't turn) - Check drive belt for breakage and the idler pulley and motor. If you can turn the drum by hand freely, likely belt or motor problem. d) Dryer noisy or vibrating - Inspect drum rollers, glides, bearings, and motor mounts for wear. 4) Step-by-step basic diagnostic checks (use a multimeter and basic hand tools) - Safety first: unplug electric dryers (or shut off breaker). For gas dryers, shut off gas and unplug. - Check continuity of the thermal fuse: locate near the blower housing or heating element area, remove leads, test with multimeter; an open fuse = replace. - Test heating element: remove access panel, visually inspect element coil for breaks, test continuity; open = replace element. - Test door switch: press the switch and check for continuity. No continuity when pressed = replace. - Check belt: open front or rear access panel and inspect; if snapped or glazed, replace belt and inspect idler pulley and motor pulley. - For gas models: visually inspect the igniter—if cracked or not glowing, it may need replacement. Test gas valve coils for continuity. 5) Basic repair/replacement guidance (common fixes) - Replacing a thermal fuse: 1. Unplug dryer (or shut off breaker). For gas dryers, shut off gas supply. 2. Access the fuse (usually on the blower housing or heating assembly). Remove screws and disconnect wires (note positions or take photo). 3. Install the new fuse, reconnect wires, reassemble, and test dryer. - Replacing a heating element (electric dryer): 1. Unplug dryer; remove access panel to reach element assembly. 2. Note wire positions and remove connectors and mounting screws. 3. Replace element assembly, reassemble, and test. - Replacing a belt: 1. Remove front or top and front panel to access drum. 2. Release tension from idler and slip belt off motor pulley and drum. 3. Install new belt around drum and through idler, seat belt on motor pulley, reassemble. - Replacing door switch or start switch: unplug, remove access panel, disconnect and swap with OEM replacement. 6) After repair - Run an empty test load to confirm operation. Check vent exhaust temperature and airflow. - If problems persist, note any error codes from the control board and consult the model-specific service manual. Safety note: Always disconnect power before servicing. Gas dryers require shutting off the gas and may need a licensed technician for gas line work. If you’re not comfortable with electrical wiring, gas components, or disassembly that requires removing many panels, hire a qualified appliance technician.
Common Symptoms
Symptoms commonly associated with this model/typical dryers: won't start, no heat or insufficient heat, long drying times, loud squealing or thumping, drum not turning, and error codes on electronic models.
Common Causes
- Open thermal fuse or high-limit thermostat (no heat)
- Broken drive belt, seized motor, or faulty idler pulley (no tumbling)
- Restricted venting or clogged lint screen (long dry times and overheating)
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
If you’re not sure which part is bad, start by checking the thermal fuse and the heating element (for no-heat issues) and the door switch (for no-start). These are inexpensive and quick to test with a multimeter.
Frequently Asked Questions
How do I confirm if TJ90TB123A is the correct full model number for my dryer?
Look for the appliance data tag (model and serial label) inside the door opening, on the door rim, on the back panel, or on the rear of the dryer. Use the exact full string printed on that sticker when searching for manuals or parts. If you only see TJ90TB123A on packaging or a partial sticker, take a photo and contact the manufacturer with that image for verification.
Can I replace dryer parts myself or should I hire a technician?
You can replace many common parts yourself (thermal fuse, heating element, belt, door switch) if you have basic tools and follow safety steps: unplug power, take photos of wiring for reassembly, and use OEM replacement parts. For gas components, major motor work, or if you’re uncomfortable with electrical tasks, hire a licensed appliance technician—especially for gas shutoff, re-lighting pilots, or complex control board troubleshooting.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.