Samsung WF45R6J0DAV/US Washer — Common Problems & What Parts Fix Them
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
This guide covers the most common problems with the Samsung WF45R6J0DAV/US 4.5 cu. ft. front-load washer — no power, won't fill, won't drain or spin, leaks, excessive vibration/noise, and specific error codes. Follow these diagnostic and repair steps in order; each numbered section targets a specific symptom and shows practical how-to steps. 1) Washer won't power on or respond - What to check first: confirm outlet is live (test with a lamp), verify the washer's power cord is fully plugged in, check household breaker/fuse. - Diagnostic steps: 1. Unplug the washer for 60 seconds, plug back in and try power. 2. If no display, test the outlet with a voltmeter or a known-good appliance. 3. If outlet is good but washer has no power, remove the rear access panel and visually inspect the control board for burn marks or swollen capacitors. 4. Check the main harness connector from the cord to the board for loose connections. - How to fix: - Replace a tripped breaker or restore power to the outlet if that's the issue. - If the control board is visibly damaged or fails voltage tests, replace the main control board (order OEM board for your exact model). 2) Washer won't fill or takes too long to fill (4E or similar water supply error) - What to check first: hot/cold water shutoff valves, inlet hoses, household water pressure. - Diagnostic steps: 1. Make sure both hot and cold valves are fully open. 2. Remove inlet hoses and check screens for debris; clean if clogged. 3. Check water pressure at the valves — low pressure can cause long fill times. 4. Test the inlet valve coil for continuity with a multimeter. Also test continuity on the inlet temperature sensor/thermistor if present. - How to fix: - Clean or replace clogged inlet hose screens. - Replace the water inlet valve assembly if coils show open circuit or valve does not actuate. 3) Washer won't drain or shows 5E/SE drain error - What to check first: drain hose routing, pump filter (if accessible), and drain pump operation. - Diagnostic steps: 1. Check the drain hose for kinks or ice blockages and make sure it's installed at the correct height (per manual). 2. Remove any visible lint or obstruction from the pump filter (front access or rear depending on model). 3. Run a drain/spin cycle and listen: does the drain pump run (a humming or whirring sound) or is it silent? 4. Disconnect power, remove access panel, and inspect the pump impeller for trapped items (coins, garment fragments). 5. Test pump motor wires for 120VAC during drain cycle (if you are comfortable) or test pump motor for continuity with a multimeter. - How to fix: - Clear obstructions in drain hose/filter. - If pump hums but doesn't pump (impeller damaged) or has no continuity, replace the drain pump assembly. 4) Washer won't spin or tumbles slowly / 'UE' unbalanced error - What to check first: load balance, shock absorbers, suspension, drive belt (if applicable), and door lock. - Diagnostic steps: 1. Make sure load is distributed evenly and not overloaded; try a small balanced load. 2. Run a spin-only cycle and listen/watch for signs of motor trying to spin but stopping. 3. Inspect shock absorbers/dampers for oil leaks or damage; check suspension springs and tub bearings by lifting and shaking the drum by hand. 4. For belt-driven models, inspect the drive belt for wear/tension. - How to fix: - Re-balance the load. Replace shock absorbers or suspension springs if worn. - Replace worn bearings or drive belt as needed (bearing replacement is more advanced — you may prefer a tech). 5) Water leaking from washer (LE error or visible leak) - What to check first: door gasket, detergent drawer, hoses, and pump housing. - Diagnostic steps: 1. Inspect the door gasket for tears, trapped items, or mold build-up that prevents sealing. 2. Run a short cycle and watch under the machine for the leak source. 3. Check detergent drawer and dispenser hose connections for cracks or overflow from using too much detergent. 4. Inspect inlet hoses and clamps for tightness and cracks; check pump housing for hairline cracks. - How to fix: - Replace torn or deformed door gasket (boot seal). - Replace damaged hoses or clamps and tighten fittings. - Replace pump if leak originates from pump housing/seal. 6) Excessive vibration or loud banging during spin - What to check first: leveling, shock absorbers, suspension springs, load distribution. - Diagnostic steps: 1. Use a level and adjust the four feet so the washer sits flat and stable. 2. Inspect and, if necessary, replace shock absorbers and suspension springs. 3. Check for foreign objects trapped between tub and outer drum (carefully maneuver drum and look). 4. Ensure shipping bolts were removed at installation (only relevant for new units). - How to fix: - Level the washer and replace worn suspension components. Remove any foreign objects. 7) Persistent odor or mold in door gasket - What to check first: detergent type/amount and door gasket condition. - Diagnostic steps: 1. Clean gasket creases thoroughly with a 50/50 solution of water and vinegar or a commercial washer cleaner. 2. Run a high-temp cleaning cycle with no clothes and a washer cleaner tablet or bleach (follow manufacturer directions). 3. Leave the door and detergent drawer open between cycles to let the interior dry. - How to fix: - Replace the door gasket if mold cannot be removed or if it's damaged. Safety note: Always unplug the washer and shut off water supply before opening panels or disconnecting hoses. Use proper personal protective equipment. If you are not comfortable working with live voltage (testing 120VAC), or replacing drum bearings or the main control board, hire a qualified appliance technician.
Common Symptoms
No power, won't fill, won't drain, won't spin, leaks, loud noise or excessive vibration, and persistent odors or mold around the door gasket.
Common Causes
- Blocked or failed drain pump or clogged drain hose
- Bad door latch/lock assembly preventing the washer from starting
- Worn shock absorbers, suspension springs, or bearings causing vibration or failure to spin
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
To confirm a faulty drain pump, run a drain cycle and listen: a healthy pump will spin and move water. If you hear a hum with no water movement or the pump does not run at all, remove the pump access panel and check for trapped debris and continuity on the pump motor with a multimeter.
Frequently Asked Questions
How do I run diagnostic mode on this Samsung washer?
Samsung models vary. Typically you can enter diagnostics by turning the dial to the 'Spin' or 'Rinse' position then pressing a sequence of buttons (consult the service manual for your exact model). If you don't have the manual, search for 'Samsung WF45R6 service mode' or contact Samsung support for the correct button sequence for WF45R6J0DAV/US.
Is it worth repairing a leaking or noisy WF45R6J0DAV/US or should I replace the washer?
If the issue is a replaceable part like a drain pump, door gasket, inlet valve, or shock absorbers, repair is usually cost-effective. Major repairs such as bearing and spider assembly replacement can be labor-intensive; compare repair cost to replacement price for your unit's age and condition. For machines older than 8–10 years or with multiple failing components, replacement may be the better option.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.