Samsung WA50M7450AW/A4 Drain Pump Replacement – How to Replace the Drain Pump
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What the drain pump does and why you might need to replace it: The drain pump removes water from the tub during the spin/drain cycles. Over time the pump can become clogged with debris, fail electrically, or wear out mechanically (noisy grinding or seizing). If the washer won’t drain, makes loud noises during drain, leaks at the base, or shows drain-related error codes, the drain pump is a primary suspect. Diagnostic and replacement steps (numbered): 1) Confirm the problem: a) Run a drain/spin or drain-only cycle and listen: is the pump silent, humming, grinding, or making a rattling noise? Does water leave the tub? Note any error code on the display (OE, 5C/5E or similar drain/overflow codes). b) Check the sink or a utility drain by activating a drain-only cycle and watching the drain hose for flow. 2) Basic checks before removing the pump: a) Unplug the washer and turn off the water supply. b) Access the drain hose at the back and lower it into a bucket or floor drain — remove any blockages from the hose and the standpipe. c) If your model has a small drain access plug or filter behind a bottom kick panel, open it and clear lint, coins, or debris. 3) Tools and parts you'll need: - Philips and flat screwdriver, socket set (7/16" or 10mm common), pliers - A shallow pan or towels for residual water - Replacement drain pump (see parts below) - Hose clamps (replacement clamps if originals are corroded) 4) Remove the washer cabinet or access panel: a) Pull washer away from wall. Unplug and turn off water. b) On many Samsung top-load models the pump is located behind the back or bottom front access panel. Remove the back panel screws (or bottom front kick panel) to expose the pump area. c) If unsure which panel, consult your model’s service manual. Work on a flat surface and keep screws organized. 5) Drain residual water safely: a) Place towels and a shallow pan under the pump area. b) Carefully loosen the lower hose clamp to the tub or remove the small drain hose to allow remaining water to drain into the pan. 6) Remove the old pump: a) Note and photograph the wiring harness and hose positions for reassembly. b) Unplug the pump electrical connector (release locking tab) and remove any wire ties. c) Loosen or remove hose clamps on the inlet and outlet hoses; slide hoses off the pump fittings (some hoses are tight—use pliers). d) Remove mounting screws or clips that secure the pump to the chassis and extract the pump. 7) Inspect and clean: a) Inspect hoses for cracks, kinks, or clogs. Replace if damaged. b) Inspect the pump housing and impeller area for broken plastic or foreign objects. 8) Install the new pump: a) Position the new pump and secure with the original screws/clips. b) Reattach hoses and secure clamps tightly (but do not over-tighten plastic fittings). c) Reconnect the electrical connector as photographed earlier. d) Reinstall any removed panels and screws. 9) Test the repair: a) Reconnect water and plug the washer in. Keep the front or back panels off if you want to visually inspect for leaks during the test. b) Run a drain or spin cycle and observe: pump should run, water should evacuate, and there should be no leaks or unusual noises. 10) Final reassembly and check: a) If no leaks and operation is normal, reattach all panels and move washer back into place. b) Dispose of old pump and any debris safely. Safety note: Always disconnect power before working on the washer and turn off water supplies. Wear gloves and eye protection when handling sharp metal edges and when draining water. If you are uncomfortable with electrical or mechanical repairs, consider contacting a qualified appliance technician.
Common Symptoms
Washer does not drain; water remains in tub after cycle; loud grinding or rattling noise during drain; drain-related error codes; leaking at bottom of washer.
Common Causes
- Clogged or obstructed pump impeller/hose (coins, lint, small clothing pieces)
- Electrical failure inside the pump motor (no spin or only humming)
- Mechanical wear or broken impeller causing lack of flow or excessive noise
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Confirm a faulty pump by running a drain-only cycle: if the pump hums but doesn't move water, or if it makes grinding/rattling noises, the pump is almost certainly bad. Also check for OE/5C/5E drain error codes and visible debris in the pump filter/hose before replacing.
Frequently Asked Questions
Can I replace the drain pump myself or do I need a technician?
Yes — many homeowners can replace the drain pump themselves if they have basic mechanical skills, the right tools, and follow safety precautions. Tasks: unplug appliance, drain residual water, remove access panel, disconnect hoses and wiring, swap pumps, and test. If you’re uncomfortable with electrical connections, have limited space to work, or if the pump is integrated in a way you’re unsure about, hire a qualified appliance technician.
How much does a replacement pump cost and how long does the repair take?
A replacement drain pump for Samsung washers typically costs between $40–$120 depending on OEM vs aftermarket. Expect the repair to take 30–90 minutes for a competent DIYer (includes draining, disassembly, replacement, and testing). Additional time may be needed if panels are corroded or bolts are difficult to access.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.