Samsung DV337AGG/XAA Dryer Thermostat — What Part Fixes This Problem?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What this part does: The dryer thermostat(s) and thermal fuse monitor and regulate the dryer temperature. The cycling (operating) thermostat closes and opens to maintain tumbling temperature; the high-limit thermostat or thermal fuse is a safety device that opens if the dryer overheats. On Samsung models like the DV337AGG/XAA, a failed thermostat or thermal fuse is a common cause of no heat, overheating, or dryers that run but don’t complete cycles. Step-by-step diagnostic and repair steps: 1) Safety first: Unplug the dryer and shut off gas at the supply if you have a gas model. Allow the dryer to cool and work in a well-lit area. Wear gloves and eye protection. 2) Gather tools: multimeter (continuity/ohms), Phillips and flat screwdrivers, nut driver set (typically 8mm or 5/16"), needle-nose pliers, camera or phone to document wiring, replacement thermostat/thermal fuse. 3) Confirm symptoms: Common thermostat/thermal-fuse symptoms include: dryer runs but won’t heat, dryer overheats and trips off, dryer stops mid-cycle, or dryer takes forever to dry. Also check for poor airflow (long dry times) before replacing parts. 4) Check vent and lint screen: Remove lint from the lint trap and inspect exhaust vent for restriction. A blocked vent can cause overheating and repeatedly blow the thermal fuse/thermostat. 5) Access the thermostats/thermal fuse: - For many Samsung front-load/stackable styles (DV3xx series), remove the back panel (or front panel on some models). Disconnect power first. - Locate the thermal fuse(s) and thermostat(s) near the blower housing or exhaust duct (small round discs or rectangular clips with 2 wires attached). 6) Visual inspection: Look for burnt or melted connectors, burn marks, broken mounting clips, or a snapped sensor element. 7) Test with a multimeter: - Set multimeter to continuity or lowest ohms range. - For the thermal fuse: remove one wire (or disconnect connector) and test across terminals. A good thermal fuse should show near 0 ohms (continuity). An open fuse reads OL or infinite resistance. - For a cycling thermostat: at room temperature it should typically show continuity. If it shows open, it’s failed. 8) Replace the failed component(s): - Note or photograph the wiring and orientation. - Remove mounting screws/clips and pull off the old thermostat/fuse. Disconnect the quick-disconnect terminals (use pliers if tight). - Install the new thermostat/thermal fuse in the same position and orientation. Reconnect wires to the corresponding terminals and secure with the mounting hardware. 9) Inspect heating element and wiring: If the heating element has a short (to ground), it can cause repeated thermostat/thermal-fuse failures and poor performance. Test heating element continuity and for ground shorts if you replaced safety devices more than once. 10) Reassemble and test: Reinstall the panel, restore power (and gas if applicable). Run an empty timed dry cycle and verify heat and that the dryer runs through the cycle without prematurely stopping. 11) If problem persists: If new thermostat/thermal fuse are good but dryer still overheats or doesn’t heat, check venting, blower wheel for restriction, heating element, and the cycling thermostat location. If electrically complex or gas valve issues exist, consider a professional technician. Safety note: The thermal fuse is a one-time safety device — never bypass it. Bypassing thermostats or thermal fuses creates a fire risk and voids warranties. Always disconnect power before testing or replacing parts.
Common Symptoms
Dryer runs but won’t heat; dryer overheats and trips off; dryer stops mid-cycle; very long drying times even with clean lint trap; scorch/melted connectors near thermostat area.
Common Causes
- Failed thermal fuse (open circuit) or high-limit thermostat (safety cutoff)
- Failed cycling/operating thermostat (no temperature regulation)
- Restricted exhaust/venting causing overheating and tripping of safety devices
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Use a multimeter to check continuity across the thermal fuse and cycling thermostat with one wire disconnected; an open (OL) reading means the part is blown and needs replacement.
Frequently Asked Questions
How do I know which thermostat or fuse my Samsung DV337AGG/XAA needs?
Open the dryer panel (with power disconnected), locate the thermostat(s) or thermal fuse and read the part number stamped on the component. If the number isn’t legible, use the dryer’s model number (DV337AGG/XAA) on Samsung’s parts lookup or a reputable parts supplier to confirm the exact OEM replacement. Testing with a multimeter (continuity) will confirm whether the part is electrically open and requires replacement.
Can I bypass the thermal fuse to get the dryer running while I wait for a replacement?
No — do not bypass the thermal fuse or thermostat. These are safety devices that prevent overheating and fire. Bypassing them is dangerous and may void warranties or insurance coverage. If the dryer won’t heat, it’s safer to replace the failed safety part before further use.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.