Part 79681582410 — What It Is, How to Identify It and How to Replace It

Understanding the Problem

Brief explanation: I could not definitively match the number 79681582410 to a specific OEM part in my offline reference set. That happens with regional SKUs, supplier-only numbers, or mis-typed part numbers. The instructions below walk you through how to identify what appliance and function the part corresponds to, how to diagnose whether it's the failed component, and how to perform a safe replacement once you have the correct replacement. Step-by-step identification and diagnostic steps: 1) Confirm the number and source: double-check the part number engraved or printed on the part and where you found it (inside the appliance, on a receipt, on a replacement label). Small transposition errors are common — re-check digits and any leading zeros. 2) Note the appliance brand and model: locate your appliance’s model and serial tag (usually on a door jamb, back panel, or inside the appliance). Write down brand + model. Many parts cross-reference to brand+model more reliably than to standalone numbers. 3) Photograph the part: take clear photos from multiple angles showing connectors, mounting tabs, labels, and any writing. This helps cross-reference in parts stores or forums. 4) Visually identify the part type: determine whether the part looks like a control board, user interface, sensor (thermistor/NTC), valve, motor, switch, thermostat, heating element, or harness. Look for common attributes: - PCBs (circuit boards): flat board, electronic components, labelled connectors - Motors: round housings, shaft, mounting bracket - Valves: solenoid coils and inlet/outlet ports - Sensors/thermistors: small bead or probe with two wires - Switches/knobs: mechanical actuators with terminals 5) Compare symptoms to part function: list what the appliance is doing wrong and match it to the identified part type. Example: appliance won’t start + spin motor not running → motor/drive or door switch or control board. Leaking at inlet and not filling → water valve. 6) Perform basic electrical checks (only if you are comfortable and follow safety steps): - Unplug or turn off breaker before touching anything. - Inspect for burns, corrosion, cracked solder joints, blown capacitors on boards, melted wiring. - If it’s a sensor/thermistor: measure resistance at room temperature and compare to expected value (you’ll need the spec — often listed in service manual). - If it’s a motor: check continuity of windings; spin freely by hand to detect mechanical seizure. - For solenoids: measure coil resistance (compare to spec) and apply appropriate voltage very briefly to see if it actuates (only if safe to do so). 7) Cross‑reference and order the correct replacement: use the appliance brand+model and the photos to search OEM parts sites, local parts stores, and large parts suppliers. Look for OEM part number and compatible alternatives. If a vendor returns a different OEM number but shows the same photos/fitment, that’s usually the correct part. Generic step-by-step replacement (applies to many parts such as control boards, switches, valves, motors): 1) Power off: unplug the appliance or shut off the correct breaker. For gas appliances, also shut off gas supply if required for access. 2) Access panel: remove the access panel(s) needed to reach the part—usually back panel, console, or front lower panel depending on appliance. Keep screws organized. 3) Document and photograph wiring: take photos or label each connector with masking tape and a marker so you can reconnect correctly. 4) Disconnect harnesses and fasteners: gently unplug wire harnesses and remove mounting screws or clips holding the part. For boards, carefully release any clip connectors; avoid flexing the board. 5) Remove and compare: remove the old part and compare it to the new replacement to ensure connector orientation, mounting hole locations, and terminal types match. 6) Install new part: secure in place, reconnect harnesses per your photos/labels, replace gasket or insulating pads if present. 7) Reassemble and test: reattach panels, restore power, run the appliance through a short test cycle to confirm operation. Watch for leaks, unusual noises, error codes. Safety note: Always disconnect power before servicing and use insulated tools. If the repair involves gas, water, high voltage, or refrigerant, consider hiring a qualified technician if you are not experienced.

Common Symptoms

Varies by part: appliance won't power on, specific functions fail (no heat, no water, won't spin), error codes, intermittent operation, visible burn or corrosion on a PCB or connector.

Common Causes

• Part failure from age, heat, moisture, or electrical surge
• Damaged wiring or connector (loose or corroded terminal)
• Incorrect or incompatible replacement part installed

Popular Parts That Fix This Problem

These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.

Frequently Asked Questions