11071812001 — What Is This Part and How Do I Replace It?

Understanding the Problem

Brief explanation: I can’t definitively identify 11071812001 without the appliance make and model because manufacturers sometimes reuse numeric strings. The safest approach is to confirm compatibility using the appliance model number or by visually matching the part. Below are step‑by‑step instructions to identify the part, diagnose whether it’s the failed component, and general replacement steps you can follow once you have the correct replacement. 1) Confirm the part identity and compatibility: a. Find your appliance model and serial number (usually on a sticker inside the door, on the frame, or behind a kickplate). b. Use the model number to look up parts diagrams on the manufacturer’s official parts site (e.g., whirlpoolparts.com, searspartsdirect.com) or a trusted parts reseller. Enter the appliance model, not just the part number. c. Compare the physical shape, mounting holes, connector types and any stamped numbers on the old part to photos in the parts diagram or listing. If the online listing shows 11071812001, confirm dimensions and connectors match. d. If still unsure, contact the manufacturer’s parts department or a local authorized service center with the appliance model and the part number printed on the piece. 2) Diagnose whether this part is the cause of your problem: a. Identify the symptoms (no power, no heat, strange noise, leak, etc.) and match them to the function of the part once identified. b. For electrical parts: test continuity with a multimeter (power disconnected). For thermal parts: test resistance against the manufacturer’s spec. For switches or sensors: verify they open/close as designed when actuated. c. Inspect the part visually for burn marks, corrosion, melted plastic, broken terminals or mechanical damage. 3) General step‑by‑step replacement instructions (once part confirmed): Tools needed: multimeter, nut drivers, screwdrivers (Phillips and flat), needle‑nose pliers, socket set, camera or phone to photograph wiring, replacement part, zip ties, and work gloves. a. Safety first: Unplug the appliance from power. If the appliance is gas, turn off the gas supply and disconnect per local code. If working on a hardwired appliance, switch the breaker off and verify with a non‑contact voltage tester. b. Access the part: Remove the appropriate access panel(s) — rear panel, control panel, or front (follow manufacturer guidance). Keep screws organized. c. Photograph wiring and take notes: Before disconnecting anything, take clear photos of the part’s wiring and how the part is mounted. d. Disconnect wiring and mounting hardware: Carefully pull connectors straight off — do not yank on wires. Remove screws or clips holding the part in place. e. Transfer mounting hardware and insulation: If the new part doesn’t come with mounting screws or rubber grommets, transfer them from the old part. f. Install new part: Mount and secure the replacement part, reconnect connectors by matching the photos and terminal shapes, ensuring firm, corrosion‑free connections. Replace any worn wiring harnesses if damaged. g. Reassemble panels, restore power/gas: Reinstall panels and screws. If gas was turned off, restore and check for leaks per the appliance instructions (soapy water test or gas leak detector). Turn power back on. h. Test the appliance: Run a diagnostic cycle or normal cycle that exercises the replaced part (e.g., start the dryer for a few minutes if heating component was replaced). Observe for proper operation and absence of error codes. 4) If problems persist: a. Re-test the new part to ensure it is not DOA (defective out of box). b. Check upstream and downstream components that interact with the part (fuses, thermostats, sensors, control board). c. If unsure, consult a licensed technician — especially for gas or high‑voltage issues. Safety note: Always disconnect power before working on any electrical appliance. For gas appliances, turn off the gas supply and consider hiring a qualified technician if you are not comfortable restoring gas connections safely.

Common Symptoms

Symptoms depend on which component 11071812001 corresponds to — common signs include: appliance won’t start, no heat (for heating parts), intermittent operation, error codes, visible damage (burn marks or melted plastic), or leaks if it’s a water/gas component.

Common Causes

• Normal wear and tear or thermal cycling causing element or thermostat failure
• Electrical surge or short that burned out switches or control modules
• Physical damage, corrosion, or moisture intrusion degrading connectors
• Poor ventilation or duct blockage (for heat components) causing overheating and failure

Popular Parts That Fix This Problem

These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.

Frequently Asked Questions