11062822101 — What Is This Part and How Do I Replace It?

Understanding the Problem

Brief explanation: I could not locate a definitive public OEM cross‑reference for part number 11062822101 in the common manufacturer databases. That usually means it's either an internal/catalog number, mis‑typed, or obsolete. To move forward you need to identify the actual physical part on the appliance, confirm its function, test it, and then replace it with the correct OEM or compatible replacement. Step‑by‑step identification and diagnostic steps: 1) Gather appliance details: note the appliance brand, full model number and serial number (usually on a sticker inside the door opening, behind the kick plate, or on the back). These let parts lookups work reliably. 2) Photograph the part in place: take clear photos (closeups and a few feet back) showing surrounding components and any stamped numbers on the part. If the part was already removed, photograph both faces and any connectors or mounting points. 3) Compare to parts diagram: use the brand's parts lookup page or a reputable parts site (AppliancePartsPros, RepairClinic, PartSelect) and search by your appliance model — not just the part number. Cross reference your photos to the illustrated parts list. 4) Identify symptoms tied to that part: correlate what the appliance does or does not do with the likely function of the component (powering, heating, draining, latching, rotating, sensing temperature, etc.). 5) Visual inspection: look for burn marks, melted plastic, broken tabs, corrosion, cracked solder joints, or disconnected wiring. Smell for burnt electronics. 6) Electrical tests (if applicable): a) Unplug the appliance first. Use a multimeter to check continuity across fuses, thermostats, heaters and windings. Note: remove one leg of the component from the circuit before testing to avoid false readings. b) For heating elements (ovens/dryers) expect low ohm continuity (commonly single to a few tens of ohms); an open reading means failed element. c) For motors/testable switches check for continuity across expected windings or switch positions. Compare to the schematic for your model. 7) Functional tests: reassemble enough to safely power the appliance (keep panels off if needed but clear of live parts) and observe behavior while following safety precautions. Use a non‑contact voltage tester if unsure. 8) Confirm replacement: once you confirm the failed part by visual and electrical tests, order the OEM part using your appliance model number and the part diagram part number. If you only have 11062822101 as a reference, give that to the parts specialist — they can look it up against your model. Generic replacement steps (applies to most serviceable parts such as boards, motors, switches, sensors): 1) Safety first: unplug the appliance and turn off water (washers/dishwashers). If working on a gas appliance, shut off gas supply and verify no open flames. 2) Access the part: remove the appropriate panel(s) — top, rear or front — using the correct driver. Keep screws and fasteners labeled. 3) Document wiring: take several photos of connectors and routing before unplugging anything. Label harnesses with tape if necessary. 4) Remove the defective part: disconnect electrical connectors, remove mounting screws or clips, and lift out the part. 5) Install replacement: position the new part, secure hardware, reconnect wiring in the exact routing and order as removed. Replace any gaskets/seals that were disturbed. 6) Reassemble and test: reattach panels, restore power/water/gas, and run a diagnostic or normal cycle to confirm the repair. 7) Final check: watch for leaks, unusual noises, error codes and ensure normal operation. Return the appliance to service and retain any packaging/return tags in case the part must be swapped. Safety note: If you are not comfortable working around high voltage, gas, or complex controls, stop and hire a qualified technician. Always unplug the appliance before opening panels and use insulated tools when working near live terminals.

Common Symptoms

Varies depending on the actual component: examples include appliance not powering on, no heat, no spin, leaks, loud grinding or clicking, door latch failing, error codes related to the part.

Common Causes

• Part number is an internal or outdated OEM catalog number not listed on public cross‑reference sites
• Actual part on the machine has failed (electrical short, open circuit, mechanical break, corrosion)
• Misidentification — the visible symptom is caused by another component in the circuit

Popular Parts That Fix This Problem

These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.

Frequently Asked Questions