10657362700 — What Part Is This and How to Fix the Problem?

Understanding the Problem

I couldn't find a definitive OEM match for part number 10657362700 in major parts databases. That doesn't mean the number is wrong — it may be an internal casting number, a regional SKU, or a typo. Use the steps below to identify the part on your appliance, confirm whether it’s failed, and replace it safely. Follow these numbered diagnostic and repair steps (finish by reading the safety note). 1) Confirm appliance brand and model - Find the appliance model and serial number tag (usually on the door frame, behind a kickplate, or on the back). Record brand, model and serial. - Search the brand’s official parts lookup (Whirlpool, GE, Samsung, etc.) and major parts retailers (RepairClinic, PartSelect, AppliancePartsPros) using the model number — not just 10657362700. 2) Physically inspect the old part - Remove the panel or access cover to expose the suspect part. Take clear photos from multiple angles and note any stamped or molded numbers on the component. - Compare the physical shape, connector types and mounting points to images from parts sites. Many parts have multiple numbers; the visible molded number may not be the seller’s SKU. 3) Identify symptom-to-part mapping - List the exact symptom(s): no power, no heat, intermittent operation, door won’t latch, motor humming, error codes, burning smell, etc. Common appliance parts that match these symptoms include control boards, thermal fuses/thermostats, door latches/switches, heating elements/igniters, motors and pumps. 4) Test the part (basic multimeter checks) - Safety first: unplug the appliance or switch off its breaker. If gas appliance, turn gas off and follow ignition-safe procedures. - For electrical components use a multimeter set to continuity or lowest ohms range: a) Thermal fuse or thermostat: expect continuity if good. Open (OL) = failed. b) Heating element/igniter: measure resistance. Typical heating elements read a few ohms to a few dozen ohms (varies by appliance). Very high or infinite = open element. c) Switches, door microswitches: actuate and check that contacts change state (open/closed) when pressed. d) Motors: check for continuity on windings (manufacturer specs vary). Short to ground indicates motor failure. e) Control board: visual inspection for burned components/capacitors; test related supply voltages only if you are comfortable and safe doing so. 5) Common replacement procedures (general, applied once you identify the component) - General prep: unplug appliance, take photos of wiring and connectors, label connectors with tape, have basic hand tools (screwdrivers, nut drivers, needle-nose pliers), and replacement part. A) Replacing a thermal fuse or thermostat (dryer or oven): 1. Unplug appliance and remove back panel (dryer) or access panel (washer/oven). 2. Locate the thermal fuse (small rectangular or cylindrical ceramic part with two spade connectors). 3. Note wire locations, disconnect quick-disconnect terminals, remove mounting screw and replace with new fuse. 4. Reassemble and test operation. B) Replacing a heating element/igniter (dryer, oven, gas range): 1. Power off and pull the appliance away from the wall. 2. Remove access panel(s) to expose the element/igniter assembly. 3. Unplug connectors, remove mounting screws, swap the assembly for the new one, double-check gasket/insulator placement if present. 4. Reassemble, restore power, and test on a short cycle. C) Replacing a door latch or microswitch: 1. Unplug and open door. Remove door seal/kick panel if required to access latch. 2. Remove fasteners holding the latch, carefully unplug connector(s), install new latch, and ensure the door actuator engages smoothly. 3. Test with door closed and run a short cycle. D) Replacing a control board: 1. Take multiple photos of wiring and display board orientation. 2. Unplug and remove control console or rear access panel to reach the control board. 3. Disconnect all harnesses (label first), remove mounting screws, swap board, reconnect harnesses, and replace panels. 4. Power on and run diagnostic or a normal cycle to verify. 6) If you still can’t locate the part number - Contact the manufacturer’s parts department with your model/serial and the photos. They can confirm the correct OEM part number and sometimes point out alternate SKUs. - Bring the old part to a local appliance parts dealer — they often match parts visually. Safety note: Always disconnect power (and gas if applicable) before testing or removing parts. If you’re not comfortable working with mains voltage, gas valves, or internal gas components, hire a licensed technician. Incorrect wiring or improper replacement can cause fire, electric shock or gas leaks.

Common Symptoms

Symptoms depend on the actual component: no power / no response, no heat, cycle won’t start, door won’t latch, motor hums but won’t run, error codes, or intermittent operation.

Common Causes

• Component electrical failure (open circuit, short to ground, failed capacitor)
• Mechanical wear or broken mounting/actuator
• Overheating or thermal trip (blown thermal fuse or thermostat)

Popular Parts That Fix This Problem

These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.

Frequently Asked Questions