Magic Chef 64HN-4TKVW Oven Temperature Sensor – What Part Fixes This Problem?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What the part does: The oven temperature sensor (sometimes called the oven probe or thermistor) measures oven cavity temperature and sends that signal to the oven control board so the oven can maintain the set temperature. If it fails the oven will run too hot, too cold, cycle erratically, or show incorrect temperatures. Step-by-step diagnostic & repair steps: 1. Safety first: unplug the oven or shut off its circuit breaker before opening panels or disconnecting wiring. 2. Locate the sensor: open the oven door and look at the back wall of the oven cavity (upper center area). The sensor is a thin metal probe protruding from the back wall, usually held by two screws and connected to a 2‑wire connector behind the oven. 3. Access the connector: depending on model you may remove the oven's back panel or pull the oven cavity forward slightly to reach the connector. Remove the screws holding the sensor and gently pull it out to access its wiring harness. 4. Visual inspection: check the sensor for obvious damage (bent/kinked probe, burned wiring, loose connector, corrosion). Inspect the connector and wiring back to the control board for breaks or burnt insulation. 5. Resistance test (multimeter): set a digital multimeter to the ohms range. Disconnect the 2‑wire connector. Measure resistance across the two sensor terminals. Typical expected reading: roughly 1,000–1,200 ohms at room temperature (70°F / 21°C) for many oven sensors. If your reading is open (OL/infinite), near 0 ohms, or far outside that range, the sensor is faulty. 6. Heat-change test (optional): with the sensor still disconnected and meter attached, have an assistant run the oven briefly and carefully (or use a heat source like a hair dryer) to warm the probe — you should see resistance change smoothly as temperature rises. No change or erratic change = bad sensor. 7. Replace the sensor: if defective, order the correct replacement sensor for model 64HN-4TKVW (see parts section). To replace: a) cut power, b) remove screws securing sensor to back wall, c) unplug the two‑pin connector, d) install the new sensor (connect harness and secure with screws), e) reassemble any panels and restore power. 8. Functional test: place an independent oven thermometer inside, run the oven at 350°F and verify actual temp vs set temp. Allow time for stabilization (15–20 minutes). If readings are still off by a consistent amount, use the oven's temperature calibration/offset procedure in the owner/service manual to adjust. 9. Final checks: ensure wiring is routed away from hot elements, screws are tight but not over-torqued, and there are no loose wires. Safety note: always disconnect power before working on internal components. If you are not comfortable accessing wiring or working inside the oven cabinet, hire a qualified appliance technician.
Common Symptoms
Oven runs too hot or too cool, temperature swings/cycling, food undercooks or overcooks, oven shows wrong temperature on display compared to an oven thermometer.
Common Causes
- Failed oven temperature sensor (open, shorted, or out-of-spec resistance)
- Damaged wiring or loose/ corroded connector between sensor and control board
- Faulty oven control board (less common) misreading a good sensor
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Confirm a bad sensor by measuring its resistance at room temperature — a good oven probe usually reads roughly 1,000–1,200 ohms at ~70°F. Open (infinite) or no change when heated means replace it.
Frequently Asked Questions
How do I test the oven temperature sensor with a multimeter?
Disconnect power and unplug the sensor's 2‑pin connector. Set a digital multimeter to ohms and measure resistance across the two terminals. At room temperature (~70°F / 21°C) many oven sensors read about 1,000–1,200 ohms. If the meter shows OL (open), near 0, or a value far outside that range, the sensor is bad. You can also apply heat and watch the resistance change smoothly; no change indicates failure.
Can a bad temperature sensor cause my oven to display an error code or not heat at all?
Yes. A failed sensor can cause the control board to detect an out-of-range temperature and throw an error code, or it can make the oven not heat because the board thinks the oven is already at the set temperature. However, some error codes may also indicate wiring or control board faults, so test the sensor and wiring before replacing the control board.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.