LSE7804ACE OEM Dryer Roller Shaft, Belt & Pulley Slides Kit – What It Fixes and How to Replace It
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What this kit is and what it fixes: The LSE7804ACE OEM kit typically contains the parts that support and drive the dryer drum: drum rollers (or roller shaft), belt, idler pulley, and plastic slides/glides. These parts wear with time and cause noisy operation, rubbing, uneven tumbling, or a drum that won’t turn. Replacing the kit restores smooth drum rotation and prevents further damage to the drum and bulkhead. Step-by-step diagnostic and repair instructions: 1) Safety first: Unplug the dryer from power. If it’s a gas dryer, turn the gas supply off and disconnect the gas line only if you are qualified — most kit replacements don’t require disconnecting gas. Work in a well-lit area with a small container for screws. 2) Confirm the symptom: Manually rotate the drum (after unplugging). Listen for grinding, squeal, or resistance. If the drum is hard to turn, noisy, or visibly wobbles, the roller/idler/belt/slide area is suspect. 3) Access the drum and components: - For most front-load drum dryers: open the door, remove the top (usually two screws at the back) or remove front panel (screws at top or bottom). For rear-access dryers, pull the dryer away and remove the rear panel. - Remove the drum belt: note belt routing before removing (take a photo). Loosen or remove the idler to free the belt and lift the drum out. 4) Inspect parts: - Rollers: spin each roller by hand. Worn rollers will be rough, wobble, or not spin freely. - Idler pulley: check the bearing — if it’s noisy, seized, or has play, it must be replaced. - Belt: look for glazing, fraying, cracks, or stretched sections. - Slides/glides and drum shaft: look for grooves or worn plastic that lets the drum rock. 5) Replace components with the kit: - Remove old rollers: pull off roller shafts and replace with new rollers and new shafts as included. - Replace the idler pulley: remove its mounting and install the new pulley (ensure proper orientation so the belt tracks in the groove). - Replace slides/glides: peel out old melted/worn slides and snap in the new glides to the bulkhead/drum seam. - Install a new belt: route the belt around the drum in the same orientation as removed; typically the ribbed side faces the drum. Slip belt over motor pulley and idler and apply tension by repositioning the idler. 6) Reassemble: Carefully set the drum back in place ensuring the belt tracks in the belt groove. Reinstall the front or rear panel and top. Reconnect any electrical connectors you removed. 7) Test run: Plug the dryer in, run a short cycle empty and listen for any abnormal noises. Confirm drum spins smoothly, no rubbing, and the dryer heats normally. 8) Final checks: After 10–15 minutes of operation, re-check for wobble and ensure no new rubbing marks appear on the drum edge. Safety note: Always disconnect power before starting. If you’re unsure about gas connections, dryer cabinet removal, or wiring, hire a qualified appliance technician. Use proper tools and support the drum when removing to avoid dropping and injury.
Common Symptoms
Loud squealing or grinding during spin, intermittent or complete failure of the drum to turn, visible drum wobble, uneven tumbling, burning rubber smell, or belt slipping/breaking.
Common Causes
- Worn or seized drum rollers (bearing failure)
- Deteriorated or glazed drive belt
- Faulty idler pulley or bearing
- Worn drum slides/glides or shaft that lets the drum rock
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Before disassembly, remove the belt and spin the drum by hand — if the drum spins easily and quietly with the belt off, the idler/belt may be the issue; if it's still noisy or rough, the rollers or slides are likely bad.
Frequently Asked Questions
Do I need to replace the entire kit or can I change only the broken part?
You can replace just the failed component, but shops and technicians often replace the entire roller/belt/pulley/slides kit because these parts wear together. Replacing the whole kit saves time, prevents repeat failures, and is good value if the dryer has moderate hours.
How long does this repair usually take and what tools do I need?
A typical DIY replacement takes 45–90 minutes for most models. Required tools: screwdriver set (Phillips and flat), nut driver or socket set (often 1/4"–5/16"), needle-nose pliers, and a flashlight. Have a camera or phone to photograph belt routing before removal.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.