LG8319W2 / PLG8319W2 — Identify, Diagnose, and Replace the Unknown LG Part

Understanding the Problem

Brief explanation: The number LG8319W2 / PLG8319W2 is not a clearly identifiable LG OEM part in common public references — it may be a revision code, packaging SKU, or an obscure on-part marking. Before ordering a replacement, you must confirm the appliance model and the exact part function. The steps below cover how to identify the part, common checks to diagnose typical failures, and general replacement instructions you can apply once the part is positively identified. Step-by-step identification and diagnostic steps: 1. Confirm appliance model and serial: locate the appliance rating plate (usually on the oven door frame, behind the kickplate, or on the back). Record the full model and serial number — common LG model formats start with letters (e.g., LRExxx, LSExxx). 2. Locate the physical part and read markings: open the cover/panel to expose the component. Take a clear photo of the part, including labels, connectors, and mounting points. Note any other numbers on the part — the same part often has an alternate LG OEM number stamped on it. 3. Match the part visually: compare your photo with OEM part diagrams (exploded view) from LG parts lookup sites or the appliance manual. Look for identical connectors, mounting screw locations, and physical dimensions. 4. Identify likely part function by location: - Control board area (back/top/rear): likely main control board, user interface board, or power relay board. Failures often produce no power, error codes, or dead display. - Igniter/burner area (gas range): part in the oven floor near burners is likely a bake igniter (symptom: oven won’t heat or takes very long to heat). - Door area / glass / latch: parts near the door hinge are door glass/latch/lock components (symptom: door won’t latch, broken glass). - Heating element area (electric oven): long tubular element in the oven is a bake/broil element (symptom: no heat or uneven heating). 5. Basic electrical checks (multimeter required): - With power OFF and plug removed, check resistance across suspected heating elements or igniter (bake element usually 10–50 ohms depending on oven). Open-circuit means element/igniter failure. - Check for continuity on fuses or thermal cutouts. A blown thermal fuse or open thermostat/limit can interrupt power to heating circuits. - For boards: inspect for burned components, swollen capacitors, or loose connectors. Visual defects often indicate board failure. 6. Look for error codes: if the oven shows an F-code or error, write it down and look up that code for your model — it often points to the failed subsystem (temperature sensor, door lock, control board, etc.). 7. Verify replacement part: once you find a candidate OEM number (from parts lookup or part marking), confirm compatibility by matching: - OEM part number from LG parts list - Connector type and pinout - Mounting points and physical size - Voltage and ratings for electrical parts General removal and replacement steps (apply after identification): 1. Safety first: disconnect the appliance from power. For gas ranges, turn off the gas supply and disconnect if necessary. 2. Remove access panels: use the appropriate screwdriver to remove the rear/top/front access panels to reach the part. Keep track of screws and heat shields. 3. Photograph wiring before disconnection: label wires or take photos so you can reconnect in the same arrangement. 4. Disengage wiring and mounting: unplug connectors (do not pull on wires). Remove mounting screws and any brackets holding the part. 5. Install the new part: position the new part, secure with screws, and reconnect all connectors exactly as removed. 6. Reassemble and test: replace panels, restore power, and run the appliance through a short test cycle. For ovens, preheat to confirm heating; for control boards, check the display and control response. 7. Final verification: monitor for correct temperature, absence of error codes, and that no new smells or smoke occur. If replacing gas ignition parts, ensure burner ignition and proper flame. If you cannot identify the part from on-unit markings: remove the part and bring the photo or the part itself to an authorized LG parts dealer or upload the picture to LG’s parts site / a reputable parts supplier and ask for identification. Safety note: Always disconnect electrical power and gas supply before working on appliances. If you are not comfortable working with gas or high-voltage components (control boards, heating elements), hire a qualified technician.

Common Symptoms

Because this marking is ambiguous, symptoms vary by actual part: dead display or no power (control board), no heating (igniter or heating element), door won't latch or broken glass (door parts), or intermittent operation (loose connectors or failing board).

Common Causes

• Part marking is a revision or packaging code — not the OEM cross-reference, leading to misidentification.
• Actual part failure due to age/wear: blown element, weak igniter, or failed control board components.
• Loose or corroded connectors, thermal cutouts, or failed sensors causing the subsystem to stop working.

Popular Parts That Fix This Problem

These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.

Frequently Asked Questions