LG Washer Door Lock (EBF61315802) – What This Part Fixes and How to Replace It
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What this part is and why it matters: The EBF61315802 is LG's door lock / door switch assembly for many front‑load washers. It mechanically latches the door and contains the microswitches that tell the control board the door is closed and locked. When it fails the washer will refuse to start, show door or lock error codes, or the door may not unlock after a cycle. Step‑by‑step diagnostics and repair (practical how-to): 1) Safety first: Unplug the washer and turn off water supply. Work on a dry, non‑conductive surface. Do not bypass the lock for testing. 2) Note symptoms / error codes: If the washer shows dE, DOOR, or a flashing lock symbol, or if the washer won’t start or won’t unlock, that points to the lock assembly. 3) Visual check: Open the door (if possible) and inspect the door strike and the boot (rubber gasket) for damage or foreign objects blocking the latch. If the strike is broken, replace it first. 4) Access the lock assembly: Most LG front‑load washers have the lock mounted behind the door seal at about 9 o’clock. Typical access: a. Remove top cover (two screws at back), slide top back and lift off. b. Open the door, remove the front boot clamp (spring clamp or screw clamp) using pliers or a screwdriver, fold the boot back to expose the lock. c. Remove the retaining screws holding the lock assembly to the front panel. 5) Electrical check with multimeter: With the assembly disconnected, check for continuity across the switch terminals (consult your model wiring diagram for exact pins). Many locks will show continuity in one state and change when locked. No continuity or intermittent readings = bad lock. 6) Live voltage check (advanced): With power reconnected and a helper to start a cycle that tries to lock, measure for ~12–24V (model dependent) at the lock harness to confirm the control board is sending voltage. If voltage is present but the lock doesn’t actuate, the lock is bad. If no voltage, the control board or wiring is suspect. 7) Replacement steps: a. Unplug washer again before replacing. b. Disconnect the wiring harness from the lock (note or photograph connector orientation). c. Remove the screws retaining the lock and remove the old assembly. d. Install new EBF61315802 in the same orientation, fasten screws, reconnect harness. e. Fold the boot back into position and re‑install the boot clamp securely (a loose clamp will cause leaks). f. Reinstall top cover and any removed panels. g. Restore power and run a short cycle to verify the door locks and unlocks and there are no leaks. 8) Final checks: Confirm no error codes, that the lock clicks and shows locked status, and that the door unlocks at cycle end. Safety note: Always disconnect power before opening the washer or touching electrical parts. Do not defeat door interlocks — running the machine with the door unlatched or bypassed is dangerous and can void warranties.
Common Symptoms
Washer won't start or recognize door; error codes like dE/DOOR or locked symbol; door won't lock or won't unlock after cycle; no audible click from lock.
Common Causes
- Worn or failed latch motor / actuator inside the door lock assembly
- Burned or failed microswitches in the lock (no continuity)
- Wiring harness damage or connector corrosion
- Door strike damage, misaligned or blocked boot seal preventing latch engagement
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Confirm failure by checking for the lock clicking when starting a cycle and measuring continuity on the lock's microswitch pins; if the control sends voltage but the lock doesn't actuate, replace EBF61315802.
Frequently Asked Questions
How can I tell if the door lock (EBF61315802) is bad or if the control board is at fault?
Start by checking for voltage at the lock connector during a cycle attempt. If the control board sends the correct locking voltage and the lock doesn’t click or actuate, the lock assembly is bad. If there’s no voltage, inspect wiring and fuses; the control board or its relay/circuit may be faulty. A multimeter continuity test of the lock’s microswitches when disconnected can also identify a failed lock.
Can I replace the door lock myself and is it difficult?
Yes — replacing EBF61315802 is a common DIY repair. You’ll need basic tools (screwdrivers, pliers, multimeter). The work involves removing the top or front access, folding back the door boot, unplugging the harness, and swapping the lock. Take photos of connector orientation, secure the boot clamp properly, and always unplug the washer before working on it.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.