KitchenAid KGRS205TSS0 Common Problems – What Parts Fix These Issues?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
The KitchenAid KGRS205TSS0 is a gas range that commonly shows problems with surface burners not lighting, continuous clicking, uneven or no oven heat, and gas smell. Most issues are caused by clogged burner ports, failed igniters/electrodes, a weak oven glow igniter, faulty safety/gas valves, or electronic control faults. Below are step-by-step diagnostics and repair actions you can take. 1) Safety first - Turn off electrical power to the range (unplug or switch breaker). Shut off the gas supply at the shutoff valve if you will be disconnecting gas components. If you smell gas strongly at any time, leave the house, avoid using electronics or open flames, and call your gas utility or emergency services. 2) Surface burners won't light or light weakly - Inspect burner caps and heads: remove caps and burner heads, clean off food debris and grease. Clogged ports are a very common cause. - Clean ports: soak removable parts in warm, soapy water; use a soft brush and a straightened paper clip or toothbrush to clear ports (do not widen ports). Dry completely before reassembly. - Check electrode (spark) position: the small electrode near the burner must be clean and properly positioned (about 1–3 mm from the burner). Bent or sooty electrodes can fail to spark or ignite consistently. - Test ignition: with power on and gas on, press a surface burner knob and observe if you hear/see the spark. If you get clicking with no flame, suspect a clogged burner, wet electrode, broken electrode wire, or faulty spark module. - Replace parts as needed: faulty electrodes, spark module, or igniter wiring should be replaced. Re-test after cleaning and replacing. 3) Continuous clicking or intermittent spark - Clean and dry all electrode areas and the drip pans — moisture or grease can cause the ignition system to keep trying to spark. - Inspect wiring and grounding. Loose or corroded wiring to the spark module or switches can cause intermittent or continuous sparking. - If cleaning/drying doesn't stop it, test or replace the spark module and individual electrode(s). 4) Oven won’t heat or oven lights briefly then goes out - Visual check: open oven door and observe the bake igniter (glow igniter). When calling for heat, the igniter should glow bright orange within 30–90 seconds. If it never glows or is very dim, it’s likely weak or failed. - Diagnostic test: with power off, disconnect the igniter and test for continuity with a multimeter. Lack of continuity indicates a failed igniter. Note: even if it shows continuity, a weak igniter can have high resistance and not draw enough current to open the gas valve — measuring exact current is for advanced testing. - If the igniter glows but the oven still won’t light, the gas safety valve may be failing (doesn’t open under weak current). Replace the igniter first, then retest. If oven still won’t light, replace the gas valve or check the wiring to the valve and control board. 5) Uneven baking or temperature offset - Check oven temperature sensor (probe): locate the sensor inside the oven and test resistance with a multimeter when the oven is at room temperature. Typical sensors read ~1100 ohms at 70°F (value varies by manufacturer) — rather than relying on the exact value, compare to the expected OEM spec or watch for open/short. - Replace sensor if out of specification. Also check oven door gasket and convection fan (if equipped) for proper circulation. 6) Gas smell - Immediate action: stop using the range, shut off the gas supply at the range and at the main shutoff, ventilate, do not switch electrical devices on/off, and call your gas company or a qualified technician. Do not attempt internal gas valve repairs unless you are a licensed gas appliance technician. 7) Control/display issues or locked controls - Reset power to the range (unplug or breaker for 60 seconds). If problems persist, check for error codes on display and consult KitchenAid documentation. A failed main control board or touchpad may need replacement. 8) Step-by-step common repair examples (oven igniter replacement) - Tools: screwdriver set, nut drivers, multimeter, work gloves. - a) Cut power and gas to the range. - b) Remove oven racks and bottom panel to access the igniter (location varies by model; consult your manual). - c) Disconnect igniter wiring harness (note orientation) and remove mounting screws holding igniter to the burner tube. - d) Replace with the OEM igniter rated for KGRS205TSS0. Reconnect wiring, reassemble panels and racks. - e) Restore power and gas, and observe ignition sequence. 9) Surface spark module replacement (general) - a) Turn off power and gas. - b) Remove cooktop (lift or unclip per model instructions) to access the spark module beneath. - c) Label and disconnect electrode leads from the old module, remove mounting screws, install new module, reconnect leads and reassemble. - d) Restore power and test all burners. Final safety note: If you are uncomfortable working around gas or you detect persistent gas leaks, electrical arcing, or if the repair requires replacing the gas valve or internal gas tubing, stop and call a licensed service technician. Gas work can be dangerous and often requires local licensing or code compliance.
Common Symptoms
Surface burners fail to light or click continuously, oven won’t reach temperature or won’t light, uneven baking, persistent gas smell, or unresponsive control/display.
Common Causes
- Clogged burner ports or dirty burner caps
- Failed spark electrode or spark module (surface ignition)
- Worn or weak oven glow igniter
- Faulty gas safety/flow valve or wiring
- Faulty oven temperature sensor or control board
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
To confirm an oven igniter failure: with the oven set to bake, observe the igniter — if it never glows, or glows very faintly and the oven won’t light, replace the igniter. If it glows normally but no flame appears, suspect the gas safety valve.
Frequently Asked Questions
Can I replace the oven igniter or spark module myself?
Yes, many homeowners can replace the oven igniter or surface spark module if they are comfortable turning off power and working with basic hand tools. Always disconnect power and gas before starting. For gas valve replacement, persistent gas leaks, or if you are unsure, hire a licensed appliance technician.
I smell natural gas near my range — what should I do?
Stop using the appliance immediately. Do not switch electrical devices or lights on/off. Open windows to ventilate, shut off the gas supply at the shutoff valve if safe to do so, leave the house, and call your gas utility or emergency services. Have a qualified gas appliance technician inspect and repair the range before using it again.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.