Kenmore 1069632682 Add-On Ice Maker Kit – What Part Fixes This Problem?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What this part is and why you might need it: The Kenmore 1069632682 is an add-on ice maker kit designed to allow owners of compatible Kenmore/Whirlpool-style refrigerators (models built without a factory ice maker) to install a mechanical ice maker assembly and connect it to the refrigerator's water supply. This kit typically includes the ice maker assembly, mounting bracket/hardware, a short fill tube, and a wiring harness or adapter. It does not always include a water inlet valve—some installs use the existing valve, other times a dedicated valve is required. Step-by-step installation and diagnostic/repair instructions: 1) Verify compatibility: Confirm your refrigerator model supports an add-on kit. Check for a blank mounting boss or screw locations inside the freezer and a wiring harness plug or connection point. If your model number does not match the kit compatibility list, do not proceed. 2) Gather tools and supplies: Flathead and Phillips screwdrivers, nut driver set, adjustable wrench, drill (if new hole is required), needle-nose pliers, tubing (1/4" OD plastic or copper depending on kit), plumber's tape, bucket, towel, and a multimeter (for diagnostics). 3) Cut water to fridge: Turn off the water supply to the refrigerator (under-sink shutoff or house valve). If there is a water filter or dispenser, turn those off as well. Pull the fridge away from the wall and unplug it. 4) Inspect mounting location: Inside the freezer, locate the pre-formed mounting bosses or the position where the ice maker mounts (typically upper-left or upper-right). Remove any access cover or plug. 5) Mount kit bracket and ice maker: Secure the kit's mounting bracket with the supplied screws into the bosses. Attach the ice maker assembly to the bracket per kit instructions—usually a slide-in and two screws to hold in place. 6) Connect the wiring: Plug the kit's harness into the refrigerator’s ice maker/adapter connector. If your refrigerator does not have an existing connector, the kit may include an adapter that wires to the main harness. Follow wire color codes and route the harness away from the evaporator fan and sharp edges. 7) Connect the water line: Attach the fill tube to the ice maker inlet. Run the supplied or existing 1/4" water line from the refrigerator water inlet valve to the kit’s copper/plastic tubing. Use compression fittings or the provided connectors. Tighten fittings hand-tight plus 1/4 turn—do not overtighten. 8) Turn water on and check for leaks: Slowly open the water supply valve and inspect all connections for leaks. Tighten as needed. Place towels/bucket under connections while you test. 9) Power up and test: Plug in the refrigerator and allow the ice maker to cycle. Manual start: most mechanical add-on ice makers have a test switch or a harvest cycle initiated by rotating the motor shaft or pressing a test button. Observe the fill: the ice maker should draw a short controlled stream of water into the mold. If the ice maker does not fill, re-check water line, inlet valve operation, and harness connection. 10) Trim and secure line: Use clamps or clips to secure tubing along the cabinet so it won’t rub or kink. Reinstall any covers and push the refrigerator back into place. Troubleshooting common install problems and how to fix them: - No fill at test: Check water shutoff, kinked tubing, or blocked fill tube. Verify the water inlet valve has 120 VAC when the ice maker calls for water (use multimeter). If the valve does not open but has voltage, replace the valve. - Slow fill: Check water pressure (should be at least 20–30 psi), partially closed shutoff valve, clogged filter, or a tiny kink in tubing. - Leaks after install: Tighten compression fittings, re-seat ferrules, or replace damaged tubing. - Ice maker doesn’t cycle: Confirm the unit is mounted level, check harness connection, inspect the motor and switch on the ice maker for continuity. Replace the ice maker if motor or thermostat is faulty. Safety note: Always unplug the refrigerator and shut off the water supply before wiring or plumbing work. If you are not comfortable with wiring or detecting 120 VAC, hire a qualified technician.
Common Symptoms
You have a refrigerator model without ice production and want to add ice; or you attempted to install an ice maker and you get no fill, slow fill, leaks, or the ice maker doesn’t cycle.
Common Causes
- Refrigerator was produced without a factory ice maker and needs a kit to add ice-making function
- Missing or blocked water supply connection or faulty water inlet valve
- Incorrect mounting, wiring, or kinked tubing after installation
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
To confirm the kit is the right fix, look inside the upper freezer for pre-drilled mounting bosses and a 4-pin wiring connector—those indicate the cabinet is prepared for an add-on ice maker. During testing, if you hear the motor click and you get no fill, the problem is likely the water inlet valve, not the ice maker itself.
Frequently Asked Questions
Will this kit work on any Kenmore refrigerator?
No. The 1069632682 add-on kit fits specific Kenmore/Whirlpool-style models designed with mounting bosses and wiring to accept an add-on ice maker. Check your refrigerator model number and the kit’s compatibility list before purchasing. If your fridge lacks the wiring harness, you may need an adapter or additional wiring.
After installing the kit, the ice maker gets power but won't fill with water. What should I check?
First ensure the water supply is turned on and the tubing is not kinked or blocked. Check for leaks at fittings. If the fill tube is clear and water pressure is adequate, verify the water inlet valve is receiving 120 VAC when the ice maker calls for water—if voltage is present but the valve doesn't open, replace the valve. Also confirm the fill tube is properly seated at the ice maker inlet.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.