Ice Maker 1067021441 – What Part Fixes This Problem?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
Brief explanation: Part 1067021441 is an ice maker assembly used in many refrigerators (commonly Whirlpool/Maytag/Kenmore platforms). It contains the motor, ejector blades, ice mold thermostat/heater, fill switch and the wiring harness connector. Replacing this assembly fixes problems caused by a dead motor, failed thermostat/heater, broken ejector, or internal electrical failures. Diagnostic and repair steps: 1. Confirm symptoms: note whether the ice maker is not making ice at all, not filling, constantly running / overflowing, or making partial fills or misshapen cubes. 2. Check water supply: verify the refrigerator water supply valve is fully open and there is good household water pressure. If the water supply is off or weak, the ice maker won’t fill. 3. Inspect fill tube: locate the plastic fill tube behind the freezer liner. If the tube is frozen, thaw with a hair dryer (low heat) or warm water and retest. A blocked/frozen tube will prevent fills even if the ice maker works. 4. Check the bail arm or fill sensor: make sure the shutoff arm (if present) isn’t stuck in the “up” (off) position and that there are no obstructions in the ice bin preventing the arm from moving. 5. Force a harvest/fill cycle: disconnect power for 30 seconds then reconnect, or use the ice maker test pins (if present) and a jumper or the fridge’s diagnostic mode to advance the ice maker through a cycle. Listen: you should hear the motor turn and the water valve click when filling. If motor turns but no water, suspect valve or supply; if no motor action, suspect the ice maker assembly. 6. Electrical checks: with the refrigerator unplugged, check the ice maker wiring harness and connector for corrosion, damage, or loose pins. With a multimeter, check continuity of the motor and heater/thermostat elements per the service manual. If the ice maker motor, thermostat, or heater shows open circuits or no expected resistance, the ice maker assembly is defective. 7. Replace part 1067021441 if diagnostics point to internal failure: order the correct part for your refrigerator model (the same part number or manufacturer-approved equivalent). 8. Replacement steps (basic): a. Unplug the refrigerator or turn off the breaker. Shut off the water supply to the fridge. b. Remove ice bin and any access panels in the freezer to expose the ice maker. c. Disconnect the wiring harness from the ice maker (note orientation and connector placement). d. Remove the mounting screws holding the ice maker and pull the unit away from the wall. e. Install the new 1067021441 ice maker: position it, secure mounting screws, and reconnect the wiring harness. f. Reinstall the ice bin and any panels, turn the water back on, and restore power. g. Force a test cycle or wait for the unit to go through its automatic cycle and verify you hear the valve and motor actions. Expect the first ice batch to take up to 24 hours. Safety note: Always disconnect power before working on electrical components, shut off the water supply before disconnecting water lines, and follow the refrigerator manufacturer’s service manual for model-specific torque and wiring procedures.
Common Symptoms
No ice production, no fill (no water entering mold), continuous cycling/overflow, motor not running, or cubes are malformed.
Common Causes
- Internal motor or electronics failure in the ice maker assembly (wear, burned motor, bad control board)
- Failed mold thermostat or heater preventing harvest
- Clogged/frozen fill tube or closed water supply
- Faulty water inlet valve or low household water pressure
- Stuck shutoff arm or obstructed ice bin
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
To confirm a faulty ice maker quickly: use the ice maker's test pins or service diagnostic to start a harvest cycle. If the motor does not run but the ice maker has power at the connector, the ice maker assembly (1067021441) is likely bad. If the motor runs but no water fills, test the water inlet valve and supply.
Frequently Asked Questions
Is part 1067021441 compatible with my refrigerator model?
Part 1067021441 is an ice maker assembly used on many Whirlpool/Maytag/Kenmore refrigerators but compatibility depends on the exact model number and production date. Check your refrigerator’s model number and compare to the parts diagram or the seller’s compatibility list before ordering.
How long does it take to replace the ice maker and how difficult is it?
Replacing the ice maker typically takes 20–45 minutes for a competent DIYer: remove the ice bin and access panel, disconnect the wiring harness, remove two or three mounting screws, swap the unit, and reconnect. Allow up to 24 hours for the first batch of ice after installation. If you’re uncomfortable with electrical checks or water connections, hire a technician.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.