GE Condenser Fan Motor (WR60X10168) — What Part Fixes This Refrigerator Problem?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What this part is and why it matters: WR60X10168 is the condenser fan motor used on many GE refrigerators. The condenser fan sits near the compressor and condenser coils and pulls air across the coils to remove heat. If the condenser fan motor fails the compressor and coils can't shed heat properly — the fridge will run warm, the compressor may run continuously or overheat, and energy use/noise will increase. Step-by-step diagnostics and repair (practical how-to): 1) Safety first: Unplug the refrigerator or turn off its breaker before you start. Work on grounded, dry surfaces and avoid touching electrical terminals with the fridge powered. 2) Locate the fan: The condenser fan is behind the rear access panel at the bottom/back of the fridge (near the compressor). Remove the access cover with a screwdriver. 3) Visual & manual check: With the fridge still unplugged, spin the fan blade by hand. It should turn freely and smoothly. If it’s stiff, gritty, or doesn't spin — the motor bearings are likely bad or the blade is damaged/obstructed. 4) Inspect for debris or rubbing: Look for ice, wiring, or debris contacting the blade or housing. Clear anything found and re-check. 5) Electrical check (multimeter): Set a multimeter to continuity or ohms. Disconnect the motor connector and check for continuity across the motor windings (you should typically see low ohms rather than open). If open/no continuity, the motor is failed. If you are comfortable and the fridge is powered (use extreme caution) you can check for 120 VAC at the motor connector when the compressor is running — no voltage indicates a wiring or control board issue rather than the motor. 6) Listen for noise: A loud humming, grinding, or knocking while the fan is running points to internal motor bearing failure. Basic replacement steps (common on GE models): 1) Unplug fridge and remove rear lower access panel to expose compressor/condenser fan area. 2) Take a photo of the motor wiring/connector for reference. Disconnect the wiring harness from the motor. 3) Remove the fan blade from the motor shaft — it usually pulls straight off (you may need to gently pry if it’s tight). If there’s a retaining clip, remove it first. 4) Unscrew the motor mounting screws/bracket and remove the old motor. 5) Install the new WR60X10168 motor into the bracket and secure the mounting screws. Make sure the motor sits in the same orientation so the blade clears the shroud. 6) Reinstall the fan blade onto the new motor shaft (ensure it is firmly seated and oriented the same way). Reconnect the wiring harness. 7) Before reattaching the access panel, plug the fridge back in and observe the fan operation — it should run quietly and the blade should not rub anything. If it runs correctly, unplug again and reinstall the access panel. 8) Return power and monitor temperature and noise over the next 24 hours. Final safety note: Always disconnect power before working on the appliance. If you are not comfortable testing live voltage, call a qualified technician.
Common Symptoms
Refrigerator runs warm, compressor runs continuously or overheats, loud humming/grinding from rear base, cooling intermittent or poor, fan blade not spinning.
Common Causes
- Motor bearings worn/seized (motor failure)
- Fan blade damaged, bent or obstructed
- Wiring harness or connector fault, or no voltage from control
- Debris/ice obstructing the fan or damaged mounting bracket
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Hand-spin the fan blade: roughness or grinding means bad bearings. Also check for continuity across motor terminals with a multimeter—an open winding means replace the motor.
Frequently Asked Questions
Can I replace WR60X10168 myself?
Yes — replacing the condenser fan motor is a common DIY job if you’re comfortable working behind the fridge and can disconnect power. Typical tools: screwdriver, pliers, and a multimeter for diagnosis. Allow about 30–60 minutes. If you’re not comfortable working with electrical connections or live-voltage checks, hire a technician.
How urgent is replacing a failed condenser fan motor?
It’s fairly urgent. A failed condenser fan will reduce heat rejection at the coils, causing the compressor to overwork, run hotter, and possibly fail. Replace the motor as soon as you can to prevent more costly compressor damage.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.