Frigidaire Gallery Ice Maker Assembly – What Part Fixes Ice-Maker Problems and How to Replace It
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What it is: The ice maker assembly in Frigidaire Gallery refrigerators is the modular unit that harvests, fills, and ejects ice into the storage bin. It contains the ice mold, the ejector blades, the sensing arm or fill sensor, the heater (for harvest on some models), and the electrical connector that drives the ice-making cycle. What it fixes: replacing the assembly fixes failures where the ice maker does not fill, does not harvest, makes tiny/partial cubes, runs continuously, or is physically damaged. Step-by-step diagnostics and repair: 1) Confirm the symptom - Is the ice bin empty? Is the ice maker not cycling at all, or is it cycling but not filling or ejecting? - Note any leaks, frost build-up on the fill tube, or ice jammed in the mold. 2) Gather tools and safety prep - Tools: nut driver (usually 1/4" or 5/16"), Phillips screwdriver, multimeter, needle-nose pliers, towel, bucket. Turn off power to the refrigerator (unplug or switch off circuit) and shut off the water supply to the fridge if you will disconnect water fittings. 3) Visual inspection - Open freezer, remove ice bin and any shelves in the way. Inspect the ice maker for visible damage, cracked mold, burnt wiring, ice jamming ejector blades, or excessive frost on the water fill tube. 4) Check the water supply and filter - A clogged filter or kinked water line can stop filling. Replace the filter if more than 6 months old, confirm water valve is open, and inspect the inlet hose for kinks. 5) Test for cycling/power (with care) - Restore power for testing only. Use a multimeter to check for voltage at the ice maker connector during a harvest cycle. Many Frigidaire ice maker modules run on line voltage—verify model specs—if you are not comfortable, skip voltage checks and proceed to swap the unit. - You can also manually trip the ice maker’s test switch (a small tab or button) to force a harvest and fill sequence—observe whether the unit heats to release ice or whether the fill solenoid runs and water enters the tray. 6) Check fill tube for freeze-up - If the fill tube is frozen, thaw it with a hair dryer on low (keep heat away from plastic) or leave the fridge off for a few hours. A frozen tube is often caused by a failed water valve, intermittent fill or frequently dumping water into the mold. 7) Decide: repair or replace - Minor jam or frost: clear ice, test again. If the mechanism is mechanically broken, wires are burnt, or the module won’t cycle/power, replace the ice maker assembly. 8) Replacement steps (typical Frigidaire Gallery ice maker assembly swap) - a) Turn off power and water supply to the fridge. - b) Remove the ice bin and any obstructing shelves. - c) Locate and remove the mounting screws holding the ice maker (usually 2 screws). Support the unit as you remove screws. - d) Pull the ice maker forward slightly, unplug the electrical connector (press the tab) and, if present, remove the fill tube coupling or disconnect any small water line to the module. Some models have the water valve at the refrigerator chassis rather than on the ice maker module itself. - e) Remove the old ice maker assembly. - f) Transfer any required parts from the old unit to the new one (thermostat/freeze sensor, bracket) only if instructed by the new part’s directions. - g) Mount the new ice maker in position, reconnect the electrical connector and water line, secure with mounting screws. - h) Turn the water back on and check for leaks at any connections. - i) Restore power. If the ice maker has a test switch, run a test cycle; otherwise wait for the unit to complete its automatic cycle. Observe the first fill—this may take a minute—then ensure the mold fills and the harvest ejects properly. - j) Reinstall the ice bin and any shelves. 9) Post-repair verification - Expect the first batch to complete in 2–8 hours. Full production to normal levels often takes 24–48 hours. Check for leaks and that cubes are properly sized. Safety note: Always cut power before disconnecting wires. If you must check live voltages, only do so if you are experienced and using insulated tools. Shut off water before disconnecting fittings to avoid flooding.
Common Symptoms
No ice production; ice maker cycles but does not fill; ice cubes are tiny or misshapen; ice maker runs continuously; ice is stuck in mold or ejector blades; leaking around the ice maker.
Common Causes
- Failed ice maker module (motor/control) or internal thermostat
- Clogged or frozen fill tube or closed/kinked water line
- Faulty water inlet valve or plumbing issue
- Physical damage to the ice tray, ejector blades, or sensors
- Electrical/harness failure or blown fuse/thermal cutout in the ice maker
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Before buying a replacement, remove the ice maker and note the model number on its label (or take a photo). If you see the unit not powering during a forced test or the mold heating element is open on an ohm meter, the module is the likely faulty part.
Frequently Asked Questions
Can I replace the Frigidaire Gallery ice maker assembly myself?
Yes — most owners can replace the ice maker assembly themselves with basic tools in 20–45 minutes. Turn OFF power and water first, remove the ice bin, unmount the old unit, unplug the connector and water line if present, then mount the new unit and reconnect. Verify model compatibility before ordering the part.
How do I find the correct replacement ice maker for my fridge?
Locate your refrigerator’s model and serial number on the tag (usually inside the fridge along the door frame or on the left/right wall). Use that model number when ordering to ensure you get the correct OEM ice maker assembly. If unsure, remove the existing ice maker and take a photo of the label or part number printed on it and match that with the replacement supplier.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.