Hey there! The info here is for educational purposes only — every appliance is different, so your experience may vary.

When in doubt, always reach out to a certified repair technician to stay safe!

FPSC2277R Oven or Surface Element Not Heating – What Part Fixes This Problem?

Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.

Understanding the Problem

If your FPSC2277R range oven won’t reach temperature, heats inconsistently, or one surface element (burner) doesn’t work, the issue is usually a failed heating component, a sensor or a control issue. Electric ranges rely on a few discrete parts — bake element, broil element, infinite switch (surface element switch), temperature sensor, and the electronic control — any of which can cause no-heat or partial-heat symptoms. Before replacing parts, simple checks often narrow the fault. Confirm the element glows when set to bake/broil, watch for error codes on the control panel, and use a multimeter to test element continuity and sensor resistance. In many cases the oven bake element or the temperature sensor is the failed part; for a single dead surface burner you’ll more often find a bad surface element or an infinite switch problem.

Common Symptoms

Oven won’t heat or reaches low temperature, oven cycles too frequently, one cooktop burner doesn’t heat, elements don’t glow, error codes or displays flashing when selecting bake/broil.

Common Causes

  • Burned-out bake or broil heating element (open circuit)
  • Faulty oven temperature sensor or bad connection causing incorrect regulation
  • Defective electronic control board or infinite switch (surface element control)

Popular Parts That Fix This Problem

These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at PartsDiscount.com — just search by your appliance model number for a guaranteed fit.

Varies by serial — common replacement listings: elements frequently sold as Frigidaire/Universal bakBake Element (oven bottom)
Varies by serial — common aftermarket/Frigidaire broil element listings. Confirm by comparing connecBroil Element (oven top)
Often sold as generic oven temp sensor — typical resistance ~1080–1100 Ω at 70°F; replace with modelOven Temperature Sensor (NTC/RTD thermistor)
Model-specific part — manufacturer part number varies. If control displays errors or won’t accept coElectronic Control / Oven Control Board
Surface switch assemblies are sold per-element size/style and model. Exact part number varies; removInfinite Switch (surface burner control switch)
Replace with matching element size and connector type for FPSC2277R — part numbers vary by exact cooSurface Element (coil or solid hotplate)
If present, replacement part number depends on model and supplier; check unit label and symptoms (noThermal Fuse / Oven Safety Thermostat
Pro tip incoming! 🧠

Helpful Repair Tip

Unplug the range (or shut off the breaker), remove the element or sensor, and test for continuity with a multimeter. A bake/broil element should show continuity; an open element means replacement. The oven temperature sensor typically reads about 1080–1100 ohms at room temperature (varies by model).

Frequently Asked Questions

Can I replace the bake element or oven sensor myself?

Yes — replacing a bake element or temperature sensor is commonly a DIY job if you are comfortable working with appliances. Always disconnect power at the breaker first. For the bake element: open the oven door, remove the mounting screws at the back of the oven cavity, pull the element forward to access the wiring, disconnect the quick-connect terminals, and install the new element in reverse order. For the sensor: remove the oven racks, unscrew the sensor from the interior wall, pull the sensor out enough to access the connector behind the panel, unplug and replace. If you’re not confident with electrical work or the issue appears to be the control board or wiring, hire a technician.

How much will it cost to fix a non-heating FPSC2277R oven?

Parts-only costs vary: bake or broil elements and sensors commonly run $25–$120 depending on OEM vs aftermarket. An electronic control board can be $150–$400 or more. Labor for a service call and repair typically adds $100–$300 depending on your area. Always confirm the exact part number for your range model/serial before ordering to avoid returns, and check if the appliance is still under warranty.

Real stories from real fixers!

Real DIY Repair Stories

Be the first to share your repair story!

Share Your Repair Story

Your experience helps other homeowners fix their appliances. Tell us how it went!

Minimum 10 characters.

No shame in calling a pro! 🛠️

Can't Fix It Yourself? Find a Local Technician

It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.

You got this! Find your part! 💪

Find the Right Part for Your Appliance

Don't guess — search your exact appliance model number at PartsDiscount.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.

Your Free Parts Videos

Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to PartsDiscount.com where you can search by model number and get the right part shipped fast.

🔔 🔔 Sign Up for the Next Video Drop! Plus Coupon Codes. Tips & More!

Join our free email list. Be the first to know about new repair videos, exclusive coupon codes, and handy tips!