Fisher & Paykel Dryer Part DE08 — What Is It and How to Replace It
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
Short explanation: "DE08" is commonly seen as a small factory or label code and is not always a unique, public OEM part number. To avoid ordering the wrong part, you should first identify the dryer model and then verify the part location and function from the model-specific parts diagram. Follow these numbered steps to identify, diagnose and replace the DE08 part (or the likely parts it may refer to). 1) Confirm the dryer model and serial: Locate the model and serial sticker (usually on the door frame, behind the door, or on the rear of the dryer). Record the model number — you’ll need it to match parts. 2) Photograph the part and label: If you can access the suspected part, take clear photos of the part including any stamped numbers or the DE08 label. Compare that photo with the parts diagram for your exact model (available on Fisher & Paykel’s website or third-party parts suppliers). 3) Use the parts diagram: Enter your model number on the manufacturer or parts site and open the exploded parts diagram. Look for the same shape/location as your photographed part and confirm the official part name and number. 4) Diagnose common candidate parts: Because DE08 is not a universal public part ID, it often points to small replacement items such as a sensor, switch, thermostat, thermal fuse, or small bracket. Diagnose the specific component using these checks: - Thermal fuse / high-limit thermostat: Test for continuity with a multimeter (should show near 0 ohms if good). If open (OL), it’s failed and needs replacement. - Door switch or door microswitch: With the door open, actuate switch and check continuity. No continuity when pressed = bad. - Moisture sensor: Visually inspect for corrosion; test resistance per service manual if available. - Wiring/connectors: Inspect for burned or loose connectors; wiggle test while observing behavior. 5) Swap or replace the part: - Power off: Unplug electric dryers or shut off gas supply AND unplug before doing any work. - Access: Remove the top/front or rear panel as required (usually a few screws and clips). Keep screws organized and take photos of wire routing. - Remove: Disconnect any connectors, remove mounting screws, and extract the old part. - Install: Mount the new part in the same orientation, reconnect wires to the correct terminals, and reassemble panels. - Test: Restore power (and gas if applicable) and run a short cycle to confirm the issue is fixed. 6) If the part is heating-related: If you are replacing a thermal fuse or thermostat because the dryer won’t heat, also check the vent/ducting and the heating element for continuity — restricted airflow or a failed element are common root causes. Safety note: Always disconnect power before opening the dryer. For gas dryers, shut off the gas supply and relight pilot or leave relighting to a qualified tech if unsure. If you’re not comfortable working with electrical components or gas lines, hire a licensed technician.
Common Symptoms
User sees a label or code 'DE08' on a small part, or experiences related dryer faults (no heat, no start, no tumble, intermittent operation) that point to a small sensor, switch or fuse.
Common Causes
- Part labeling (DE08) is an internal factory code and not the model-specific published part number
- Component failure — thermal fuse, thermostat, door switch, moisture sensor, or wiring fault
- Related system issues — clogged venting, burned connectors, or failed heating element causing secondary component failure
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Confirm the faulty part by photographing the part label and matching it to the model-specific exploded parts diagram — then test it with a multimeter for continuity before ordering a replacement.
Frequently Asked Questions
How do I know if DE08 is really the part I need?
Check your dryer’s model/serial plate, take a clear photo of the part and the DE08 marking, and then compare with the exploded parts diagram for that exact model. If possible, test the component with a multimeter (continuity or resistance) to confirm failure before ordering a replacement.
Can I replace a DE08-labeled part myself?
Yes — if you’re comfortable with basic appliance repair: unplug the dryer, remove the appropriate access panel, photograph wiring, disconnect connectors, swap the part, then reassemble and test. For gas dryers or if the replacement requires extensive disassembly, consider hiring a qualified technician.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.