EFME617SIW0 Dryer Drum Rollers – What Part Fixes This Problem?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
Brief explanation: Drum rollers (also called support rollers) support the dryer drum and allow it to spin smoothly. On many dryers these are small wheels with bearings mounted on shafts at the front and rear of the drum. When rollers wear out the drum can squeal, rumble, make intermittent thumps, scrape or become hard to turn by hand. Step-by-step diagnostic and repair steps: 1) Confirm the symptom: With the dryer empty, open the door and try to rotate the drum by hand. Note rough spots, scraping, wobble, or a grinding sound. Also run a short heat cycle and listen for squeaks or thumps. 2) Unplug dryer and cut power: Always disconnect electrical power (or flip the breaker) before working on the appliance. 3) Access the drum/rollers: For most top- and front-load electric/gas dryers (including models similar to EFME617SIW0) you will remove the lint screen, the top cover or front panel, and the front bulkhead to access the drum. Support the drum as you remove panels so it doesn’t fall. 4) Inspect rollers visually: Look at each roller wheel and bearing. Bad rollers show flat spots, heavy rust, play on the shaft, wobble, cracks, or seized bearings (roller won’t spin freely on the shaft). 5) Check drum shaft and support posts: Inspect the drum shaft ends and the roller shafts for scoring or excessive wear. Also check felt seals or glide pads at the front of the drum for wear — worn glides can mimic roller noise. 6) Verify other parts: While you’re in there, spin the idler and check the idler pulley and motor shaft bearing for roughness. A noisy idler can be mistaken for bad drum rollers. 7) Source the correct roller kit: Use the machine model EFME617SIW0 and the serial number to order the exact OEM roller kit or an aftermarket kit that lists that model. Roller kits typically include 2 or 4 rollers plus shafts and mounting hardware. 8) Replace rollers (typical procedure): a) Remove the drum: lift drum out of the cabinet (may require tilting up and pulling forward). b) Remove old rollers: unscrew or pull the roller retaining bracket and slide rollers off their posts. Clean the posts of debris and rust. c) Install new rollers: press the new roller bearings onto their mounts and secure with the original brackets/fasteners. Ensure rollers spin freely on their shafts. d) Reinstall drum and check alignment: seat the drum on the new rollers and ensure the drum turns smoothly by hand with minimal lateral play. e) Reassemble dryer and test: restore panels, reconnect power, run dryer empty and listen for improved operation. 9) Test thoroughly: Run the dryer through a full cycle to confirm noise/squeak/thump is gone and that the drum tracks true. Safety note: Always unplug the dryer or disconnect power at the breaker before starting any repair. If the dryer is gas-fired, turn off the gas supply and work in a well-ventilated area. If you are not comfortable with disassembly, consider a professional technician.
Common Symptoms
Loud squealing or rumbling during rotation, intermittent thumping, scraping noise, drum hard to turn by hand, uneven wear on drum edges.
Common Causes
- Worn or seized roller bearings causing rough rotation
- Flat spots or cracked roller wheels causing thumping
- Damaged drum glides or shaft wear increasing lateral play
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
To confirm rollers are bad: with the drum removed, spin each roller by hand — a healthy roller spins freely and quietly; a bad roller feels rough, squeaks, or won't spin at all.
Frequently Asked Questions
How long does it take to replace dryer drum rollers?
For an experienced DIYer it typically takes 45–90 minutes: unplug the dryer, remove panels, lift out the drum, swap rollers, reassemble and test. If you need to order the wrong part it will add more time.
Can I replace only one bad roller or should I replace them all?
Replace all rollers on the same axle or all support rollers at once. When one roller is worn the others are often close behind — replacing them together ensures even wear and saves you repeating the repair soon.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.