Samsung DV45H7000EWA2 Heating Element – What Part Fixes This Problem?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What the heating element does: The heating element assembly generates the hot air your dryer uses to dry clothes. If the element is open, damaged, or shorted, the dryer will run but won’t produce heat, or it may overheat and trip safety devices. Diagnostic and repair steps (numbered): 1. Verify the symptom: Confirm the dryer tumbles but produces little or no heat. Also note if the dryer heats intermittently, trips a thermal fuse, or blows a circuit breaker. 2. Check airflow first: Remove the lint from the dryer lint trap and disconnect the exhaust vent to check airflow with the dryer running (briefly). Restricted venting can cause long dry times or overheating that damages the element. Fix venting problems before replacing parts. 3. Confirm basic power: Ensure the dryer is getting full voltage (for electric dryer usually 240V). If one leg of power is missing the dryer may tumble but won’t heat. If you’re not comfortable measuring voltage, skip to a technician. 4. Test the thermal fuse(s): The thermal fuse is a one-time safety device that will be open if the dryer has overheated. Remove power, locate the thermal fuse (typically on the blower housing or exhaust path on Samsung models) and check continuity with a multimeter. If open, replace the thermal fuse — this often fixes a no-heat symptom. 5. Test the heating element for continuity: With power disconnected, access the heating element terminals and measure resistance across the element. A good element typically shows a low resistance (often in the low tens of ohms). If you see infinite resistance (open) the element is bad and must be replaced. If you see a short to ground (continuity from element terminal to the metal housing), the element is shorted and must be replaced. 6. Inspect thermostats and high-limit thermostat: Test the cycling thermostat and high-limit thermostat(s) for continuity. If any are open they will prevent the element from powering. Replace any open thermostats. 7. Inspect wiring and control board: Check for burned connectors, melted insulation, or failed relays/contactors on the control board. Loose or corroded connections between the element, thermostats, and control can cause intermittent heating. 8. Replace the heating element if identified as faulty: Follow the step-by-step replacement instructions below. Step-by-step heating element replacement (practical how-to): 1. Safety first: Unplug the dryer or switch off the house circuit breaker supplying the dryer. Confirm power is off. 2. Access the element housing: On most Samsung models (including DV45H7000 series), the heating element is accessed from the rear. Move the dryer away from the wall, remove the vent, then remove the rear access panel (usually removed by unscrewing several screws). 3. Photograph and label connections: Before disconnecting anything, take photos of the wiring and note the terminal positions so you can reconnect the new element exactly like the old one. 4. Remove wires and mounting hardware: Disconnect the wires from the heating element terminals and remove the screws or clips that secure the heating element assembly to the housing. On some models you may need to remove the drum or a few additional panels to gain clearance. 5. Remove the old element: Pull the element assembly out and inspect the housing for damage or charred insulation. Clean out any lint build-up in the housing and around the blower. 6. Install the new element: Position the new element assembly, secure it with the mounting screws or clips, and reconnect the wires to the correct terminals using your photos/notes. 7. Reassemble: Replace the rear panel, reconnect the vent, push the dryer back into place, and restore power. 8. Test: Run a short cycle and verify the dryer produces heat. Check for proper airflow and listen/watch for any unusual noises. Safety note: Always disconnect power before servicing. Heating elements and surrounding metal can have sharp edges — wear gloves and eye protection. If you are not comfortable testing electrical circuits or working with 240V, hire a qualified appliance technician.
Common Symptoms
Dryer tumbles but doesn’t heat or heats weakly; very long dry times; dryer trips thermal fuse or shuts off due to overheating; burning smell or visible break in the element coil.
Common Causes
- Broken or open heating element coil
- Blown thermal fuse or failed high-limit thermostat
- Faulty cycling thermostat or temperature sensor
- Poor electrical supply (lost 240V leg) or damaged wiring
- Restricted venting causing overheating and element damage
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
With power off, measure continuity across the two heating element terminals — a good element typically reads a low resistance (often in the low tens of ohms). Infinite (OL) = replace; continuity to the metal housing = shorted (replace).
Frequently Asked Questions
How do I know if the heating element is really the problem?
Start with airflow and power checks. Then, with the dryer unplugged, test the heating element for continuity with a multimeter. If the element shows infinite resistance (open) or is shorted to the housing, it needs replacement. Also check the thermal fuse and thermostats — a blown thermal fuse often causes a no-heat symptom and may point to an overheating problem rather than the element itself.
Can I replace the heating element myself on a Samsung DV45H7000EWA2?
Yes — if you’re comfortable with basic electrical safety and simple tools. Key steps: disconnect power, remove the rear access panel, label and photograph wiring, remove the old element, install the new one, and reassemble. If you’re unsure about working with 240V circuits, testing components with a multimeter, or if there is evidence of control board damage or severe wiring melt, hire a qualified appliance technician.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.