DC64-00828B Moisture Sensor Assembly — What Part Fixes Dryer Auto-Dry Problems?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What this part is and why it matters: The DC64-00828B is the moisture (humidity) sensor assembly used in many Samsung dryers. The sensor reads moisture level in the drum and signals the control board to end the cycle when clothes are dry. When it fails the dryer’s Auto Dry/Normal cycles will be inaccurate — clothes may be over-dried, under-dried, or the dryer may stop too early or run excessively. Diagnostic and repair steps (numbered): 1. Confirm symptoms: note whether Auto Dry stops too soon, leaves clothes damp, or the dryer runs much longer than expected. Also check for error codes on the display and whether timed cycles work normally. 2. Clean the sensor first: remove the lint screen and wipe the metal sensor pads (located on the drum near the lint trap opening) with a soft cloth and isopropyl alcohol to remove fabric softener residue. Re-test the dryer — many faults are solved by cleaning. 3. Run a manual test: place a damp towel over the sensor bars and run an Auto Dry cycle or diagnostic moisture test (consult your model’s tech sheet or service mode). If the dryer doesn’t respond (doesn’t shorten the cycle or change indicators), the sensor or wiring is suspect. 4. Check wiring and harness: unplug the dryer, remove the front/top access (model dependent) and inspect the sensor harness and connector for corrosion, breaks, or loose pins. Repair or replace damaged wiring. 5. Multimeter test: with the harness disconnected, measure continuity and resistance across the sensor contacts. You should see a change in resistance when the contacts are touched with a damp cloth (dry = high/near-open, wet = lower). Exact values vary by model; the important result is change in reading when wet vs dry. 6. Control board check: if the sensor and harness test OK but the dryer still misbehaves, test the signal to/from the control board in service mode or consult service manual. Sometimes the control board’s sensor input circuit fails and will not recognize a good sensor. 7. Replace the sensor assembly (if cleaning and wiring checks fail): obtain OEM DC64-00828B, unplug power (and turn off gas at the supply on gas models). Access the sensor by removing the lint trap housing or the front/top panel (varies by model). Disconnect the harness, remove mounting screws or clips, swap in the new DC64-00828B, reconnect the harness and reassemble. 8. Verify operation: after replacement, run an Auto Dry cycle with damp clothes and confirm drying time shortens appropriately and clothes are not over-dried. 9. Final checks: clear any stored error codes and run a few loads to confirm consistent behavior. Safety note: Always unplug the dryer before doing electrical tests or removing panels. For gas dryers also shut off the gas valve. If you’re not comfortable working with appliance electrics or internal gas connections, hire a qualified technician.
Common Symptoms
Auto-dry stops too early or leaves clothes damp, dryer runs much longer than normal in sensor cycles, inconsistent drying from load to load, or dryer does not respond when you cover the sensor bars with a damp cloth.
Common Causes
- Contaminated or corroded moisture sensor bars (residue from dryer sheets/softeners)
- Failed moisture sensor assembly (DC64-00828B)
- Damaged sensor wiring or connector or a faulty control board input
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Before replacing, thoroughly clean the metal sensor bars with isopropyl alcohol and a soft cloth — residues from dryer sheets often cause false readings and cleaning fixes many 'sensor' problems.
Frequently Asked Questions
Can I fix sensor problems by just cleaning it or do I need the DC64-00828B?
Cleaning the metal sensor bars with isopropyl alcohol often fixes false readings caused by fabric softener or dryer sheet residue — try this first. Replace the DC64-00828B only if cleaning and wiring checks do not restore proper sensor behavior.
How do I test the DC64-00828B to know if it’s bad?
Power off and disconnect the harness, then use a multimeter across the sensor contacts. You should see a notable change in resistance or continuity when the contacts are dry versus when you touch them with a damp cloth. If the readings do not change or show an open circuit in both conditions, the sensor assembly is likely bad and should be replaced.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.