Amana NTW4519UW2 / NTW4519YW2 Starter (Selector) Knob — What Part Fixes This?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
What this part is and why it matters: The "starter" knob on Amana NTW4519UW2 / NTW4519YW2 is the user control (cycle/selector or start knob) you turn to pick a wash program and/or start the washer. The knob itself is usually a plastic appliance that slips onto a splined control shaft. When the knob fails (stripped splines, cracked plastic, or a broken retaining clip) you can't select cycles reliably or the washer won't start. Diagnostic and repair steps: 1) Visual inspection: Unplug the washer. Inspect the knob for obvious cracks, missing pieces, or a loose fit. If the knob turns freely without engaging the shaft or it wiggles side-to-side, the knob is likely worn or broken. 2) Test engagement: With the washer unplugged, pull the knob straight off. Inspect the inner bore (spline shape) and the metal/plastic shaft on the control. If the knob bore is rounded or the splines are worn, the knob needs replacement. If the shaft splines are damaged, the control shaft or the whole console may need replacement. 3) Check the function of the control behind the knob: After removing the knob, rotate the control shaft with pliers gently. Listen/feel for detents and observe whether the timer/program disk (or electronic control) responds — if nothing changes, the problem could be a failed switch or timer, not just the knob. 4) Order the correct part: Knobs can be model-specific. Use your full model number (NTW4519UW2 or NTW4519YW2) to order the OEM selector/start knob. If you prefer a universal knob, confirm spline count and shaft diameter match before ordering. 5) Replace the knob (basic): Unplug washer. Pull the old knob straight off. Clean the shaft of dirt. Align the knob's spline/flat with the shaft and push firmly straight on until fully seated. Test operation by rotating to cycles and attempting to start the washer. 6) Replace the knob with screw/retainer (if present): Some knobs have a small retaining screw or clip. Remove the console trim if necessary: open lid, remove two hidden screws at the rear of the top panel, tilt the console forward (or pull straight up on snap-fit bezels), access the knob mounting, remove any retaining screw, swap the knob, reinstall retainer and console, and test. 7) When the shaft is damaged: If the shaft splines are stripped or the internal control (timer/module) does not react when you rotate the shaft, you will need to replace the control/timer or control assembly. That requires removing the console, disconnecting wiring, and swapping the module. Follow OEM instructions or call a technician if unsure. Safety note: Always unplug the washer and turn off the water supply before working on controls. If you need to remove the console or electronic control, label wiring connections or take photos so you can reconnect everything correctly.
Common Symptoms
Knob spins freely or wiggles; cycle selection doesn't change; washer won't start when knob is turned; cracked or missing plastic on knob; retained screw/clip broken.
Common Causes
- Worn or stripped knob splines (plastic bore worn from use)
- Broken/cracked plastic or retaining clip that holds the knob on
- Damaged control shaft or failed timer/electronic control behind the knob
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
To confirm it's the knob (not the control), pull the knob off and rotate the exposed shaft with pliers — if the washer responds (cycles change or starts), the knob is bad. If the washer does nothing, the control/timer is likely the problem.
Frequently Asked Questions
Can I fix a loose spinning knob without replacing the control?
Yes — if the shaft splines are intact and only the plastic knob is worn, replacing the knob will fix it. Pull the knob off, verify the control shaft looks fine, then fit a new OEM or compatible knob that matches the spline pattern. If the control shaft splines are stripped or the control doesn't respond when you turn the shaft, you'll need a control/timer replacement.
Can I use a universal knob from a hardware store?
Sometimes. Universal knobs can work if the spline count, bore shape (D-flat, round with a flat, or splined), and shaft diameter match. Measure the shaft and compare to the universal knob specs. For best fit and long-term reliability, OEM knobs ordered by model number are recommended.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.