Amana NED7300WW1 Dryer Belt Replacement – What Part Fixes This Problem?
Need the replacement part? Search your model number at for guaranteed fit and fast free shipping.
Understanding the Problem
Brief explanation: The dryer drive belt wraps around the drum and connects to the motor so the drum rotates. On an Amana NED7300WW1 a worn, glazed, stretched, or broken belt will prevent the drum from turning (or cause slipping, thumping, or squealing). Below are clear diagnostic and step-by-step repair instructions. 1. Verify the symptom and isolate the belt: - Symptom check: If the motor runs (you hear it) but the drum doesn't turn, or the drum turns only when you push it, the belt is likely broken or slipped. If you hear squeal or thump as drum turns, the belt may be glazed, frayed, or riding on a worn roller. - Manual drum test: With power OFF and unplugged, try to rotate the drum by hand. If it turns freely with no resistance and you can see a snapped belt or no belt, it's the belt. If it’s hard to turn, inspect rollers and motor bearings. 2. Tools and prep: - Tools: Phillips and flat screwdrivers, socket set (1/4" and 3/8"), needle-nose pliers, work gloves, flashlight. Replacement belt and optional idler pulley/rollers if worn. - Safety: Unplug dryer and turn off gas (if gas dryer) before starting. Work in a well-lit area. 3. Access the belt and drum: (Common for many Amana top/control-panel models) - Unplug dryer. Remove lint screen and two screws under the lint opening to release top panel or use screw locations on front top. Lift top and prop or hinge back. - Remove front panel: disconnect door switch wire harness (note orientation) then remove screws that secure the front panel and lift panel away. If your model uses clips, gently unclip. 4. Inspect belt and related parts: - Look for a snapped belt, missing ribs, glazing (shiny hard surface), or oil contamination. Check idler pulley and motor pulley for smooth rotation and no wobble. Check drum rollers (if present) for wear and rough spots. 5. Replace belt (how-to): - Remove the old belt: If broken, remove pieces. If still on, slip belt off motor pulley and idler pulley and pull drum forward and out of the cabinet (support drum to avoid dropping). - Fit new belt: Route new belt around drum so the ribbed side contacts the drum grooves (ribs face the drum), wrap belt around motor pulley and idler assembly. On most installations the belt crosses under the drum with the idler applying tension on the smooth (outside) side of the belt — follow belt routing diagram on dryer or manual. - Reinstall drum: Slide drum back into position with rear drum lip seated in rear drum support and front edge fitting into front bulkhead. Ensure belt sits in the drum groove and not pinched. - Re-tension: Reposition idler so belt is snug and the drum turns freely but with firm tension. 6. Reassemble and test: - Reattach front panel and door switch harness. Lower top and secure screws under lint filter. Restore power. Run dryer on air tumble or timed dry to confirm the drum spins smoothly and no strange noises occur. 7. When to replace other parts: - If belt failure was due to seized idler or worn rollers, replace idler pulley and drum rollers at the same time. A new belt on worn rollers will fail quickly. Safety note: Always unplug the dryer and shut off gas (if applicable) before servicing. Work on a stable surface, keep fingers clear of sharp sheet metal edges, and label disconnected wires to ensure correct reassembly.
Common Symptoms
Drum won't turn even though motor runs; visible broken belt; loud squealing or thumping during spin; drum slips or tumbles irregularly.
Common Causes
- Drive belt worn, glazed, stretched or broken
- Seized or worn idler pulley causing excess wear or belt slipping
- Worn drum rollers or motor bearings allowing misalignment and premature belt failure
Popular Parts That Fix This Problem
These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.
Helpful Repair Tip
Confirm belt failure by unplugging the dryer and trying to turn the drum by hand; a snapped belt, glazed ribs, or missing ribs are immediate indicators. Also listen: motor runs but drum doesn't turn = almost always belt or idler problem.
Frequently Asked Questions
How much does it cost to replace the dryer belt on an Amana NED7300WW1?
Part cost for a dryer belt is usually low (often $10–$30 for the belt). If you also replace idler pulley or rollers the total parts cost may be $25–$80. Labor (if you hire a technician) varies by region but expect 45–90 minutes of shop time. DIY replacement is common and straightforward with basic tools.
Can I use a universal dryer belt or do I need the exact Amana part?
You can use a compatible universal belt if it matches the correct length and rib profile, but it's best to confirm size from the model tag or fit a belt specified for Amana NED7300WW1. If rollers or idler are worn, replace them too — a new belt on old support parts will fail prematurely.
Related How-To Videos
Real DIY Repair Stories
Be the first to share your repair story!
Share Your Repair Story
Your experience helps other homeowners fix their appliances. Tell us how it went!
Can't Fix It Yourself? Find a Local Technician
It's perfectly okay to call a professional. Some repairs require specialized tools, deep teardowns, or dealing with complex systems that are better left to the pros.
Find the Right Part for Your Appliance
Don't guess — search your exact appliance model number at ProsourceParts.com to find the correct OEM compatible replacement part. They offer fast free shipping, guaranteed fit, and thousands of parts in stock.
Your Free Parts Videos
Whether your dishwasher won't drain, your dryer stopped heating, or your fridge isn't cold, we've created simple repair guides for the most common appliance problems homeowners face. Each guide explains what's going wrong, the most likely causes, and which replacement parts fix the issue. When you're ready to order, we link directly to ProsourceParts.com where you can search by model number and get the right part shipped fast.