11024722300 — What Is This Part and How Do I Replace It?

Understanding the Problem

Brief explanation: I cannot find a definitive, brand-specific match for part number 11024722300 in my parts database without the appliance brand and model. Many OEM part numbers are reused or cross-referenced differently by manufacturers, so the fastest way to get an exact identification is to confirm the appliance make/model or send a photo of the part and the label. Below are practical, step-by-step instructions you can follow now to identify the part on your appliance, diagnose whether it's failing, and replace it safely. Step-by-step identification and diagnostic steps: 1. Confirm appliance details: locate the appliance model and serial number (usually on a sticker inside the door, on the back, or on the frame). Record brand, model, and serial number. 2. Inspect the part: remove the access panel that exposes the part (see safety steps below). Look for a printed or molded part number on the part itself — sometimes it differs slightly from what’s on your paperwork. Photograph the part and the surrounding area. 3. Cross-reference: use the appliance model + the printed part number in the manufacturer parts lookup (Whirlpool, Maytag, KitchenAid, LG, Samsung, etc.) or at major parts suppliers to get exact compatibility and a description of the part. 4. Identify function by location: the location tells you a lot — a part on the rear lower area of a dryer is likely a motor, belt, idler, or heating component; a part behind the fridge's rear lower panel is likely the compressor, start relay, or condenser fan; inside a dishwasher lower tub it's likely the pump or motor; on a washer's front tub it could be a door lock, water valve, or control board. 5. Visual and electrical checks: visually inspect for cracks, burn marks, melted plastic, corrosion, or fluid leaks. For electrical components, with power off, disconnect the part and check continuity with a multimeter. For sensors, check resistance against the spec in the service manual. 6. Functional test: if safe and possible, power the appliance and run a diagnostic mode or a short cycle to observe the fault while monitoring the suspected part (do this only if you’re comfortable and understand the risks). 7. Order the correct part: once you have the confirmed part number and appliance model, order an OEM replacement or a verified aftermarket equivalent. Replacement steps (general, adapt to the actual part once identified): 1. Safety first: unplug the appliance. If it’s a gas appliance, turn off the gas supply. If it’s water-connected, shut off the water supply and disconnect if required. 2. Prepare workspace: move appliance away from the wall, place towels or cardboard under to catch small parts, have screwdrivers, nut drivers, pliers, and a multimeter ready. 3. Document wiring: take clear photos of the part and all connector positions so you can reconnect correctly. Label wires with tape if multiple look similar. 4. Remove covers: remove screws and access panels to reach the part. Keep all fasteners in a container and note their locations. 5. Disconnect the part: remove electrical connectors, ground wires, hoses, or mounting screws. If connectors are stuck, gently wiggle while pulling straight out; avoid pulling on wires. 6. Install new part: transfer any mounting brackets or sensors to the new part if needed, position the new part, secure with screws, reattach hoses and electrical connectors using your photos/labels as a guide. 7. Reassemble and test: replace panels and screws, restore power, water, or gas, then run a short cycle to verify the repair. Observe for proper operation and leaks. 8. Final check: ensure no error codes remain, listen for unusual noises, and confirm the appliance performs as expected. Safety note: Always disconnect power before working on electrical appliances. For gas or sealed refrigerant systems, do not attempt internal repairs unless you are certified; contact a licensed technician. If you are unsure at any step, stop and get the exact part identification or professional help.

Common Symptoms

Symptoms vary depending on which component 11024722300 corresponds to; common signs that a part needs replacement include: appliance won’t start or complete cycles, unusual noises, leaks, no heating or cooling, error codes, or intermittent operation.

Common Causes

• Component electrical failure (open circuit, short, or intermittent connector)
• Mechanical wear or broken mounting causing improper function
• Age-related degradation (seals, plastics, or contacts failing)
• Contamination or corrosion from water, lint, or heat

Popular Parts That Fix This Problem

These are the most common replacement parts that fix this problem. When you're ready to order, click below to find the right part at ProsourceParts.com — just search by your appliance model number for a guaranteed fit.

Frequently Asked Questions